Jump to content
SAU Community

Recommended Posts

good waste of time :P lol did it... car didnt run bad but revs did drop after a huge flutter... was pretty sick but y fuel economy would half if i left it there!!! soo addictable :P good for a laugh but dont wona get looked at ne more than i need to

  • Replies 188
  • Created
  • Last Reply

Top Posters In This Topic

I've ran mine since I can remember with a blocked off BOV.

With the ceramic turbo running 1bar I covered around 100,000km's on the rb20det, then pulled it out for the rb30det. Still in good nick. I went a VG30 which was good for another 50,000km's and was still fine when I pulled that off, the Garrett gt30 I now run still doesn't use a BOV.

The GT30r has covered around 40,000km's now. Damn time flies. :S

The bov is there for emission reasons. Without a bov look what it does to your afr's on and afm voltage as you come off the throttle which causes stalling, back fires and some times flamage. Another issues is the strain it puts on your joiners/clamps. I had to replace some with t-bolts.

The reason I went no bov is the stocker was for the part throttle drivability. No bov you grab the next gear and boost is just there. Without a bov it felt laggier on gear changes as I presume it takes longer to fill the FMIC and piping than it does to regain the 'slight' speed the compressor may loose due to pushing against a pressure source.

Shaun/Boostworx runs track cars with no bov, no issues related to no bov. I know of multiple high powered RB30et's without issues running no bov.

No more need to be said!!!!

  • 2 years later...

Okay, old thread here. sorry, want to blank off my bov so I dont look like a fag when I drive around. Used search came up with this and a heap of old closed threaDs that seem to make it sound like IF u blank of ur bov it just makes ur car get that other gay flutter noise not silencing it completely. Is this correct?????

you own a turbo car but dont like the bov noise? have you got an aftermarket bov?

yes, if you block it off it will flutter.

Did have an aftermarket atmospheric one when I got the car which said LOOK AT ME, then swapped the mechanic who took it through regency for me for his stock one. But its still too loud oh well guess Ill just have to put up with it in exchange for a nice fast car.

The one that was on it also made a fluttery type sound when u gave it a rev.........I dont know fark all bout them though

you probably had an adjustable one, where you can stiffen to spring so it only vents a small amount of pressure and flutters the rest. if you have a pod, try fitting a stock airbox to quieten the induction noise and see how you go

Just out of curiosity.... everyone is saying use coke cans, mountain dew cans etc. Are they being used as blanking plates? Not entirely sure how its done.

I've got a 32 with an rb20 with an aftermarket BOV. Was just wondering what the deal is with making up blanking plates and what everyone has used.

Okay, old thread here. sorry, want to blank off my bov so I dont look like a fag when I drive around. Used search came up with this and a heap of old closed threaDs that seem to make it sound like IF u blank of ur bov it just makes ur car get that other gay flutter noise not silencing it completely. Is this correct?????

As Damo has mentioned earlier. You cannot have a turbo car with a pod filter and not expect any induction noise at all. Even with the stock BOV it makes a loud woooosh sound. But if you block/blank it off all the pressure has to go somewhere and since the BOV is blocked it will just go back through the system hence why it makes the huge (in my case) flutter.

Just out of curiosity.... everyone is saying use coke cans, mountain dew cans etc. Are they being used as blanking plates? Not entirely sure how its done.

I've got a 32 with an rb20 with an aftermarket BOV. Was just wondering what the deal is with making up blanking plates and what everyone has used.

Totaly acceptable use of thread bump guys

Take your bov off grab a pen trace around it and cut coke can up a good pair of scissors is all that's needed

Presto spot on Steve. I have been using a coke can pretty much since i have ever owned the car lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...