Jump to content
SAU Community

Recommended Posts

Hey all,

Ive searched through the RB26 modifaction section and have come up with wht i think should be ok for what im after..

But not being that knowlegable the numbers and turbos all mix into each other etc etc lol...

Im just after someone to look over what i have already got and what i am currently searching for and either say yes that would be sutible for what im after or no mayb you should look at this..... etc.

First off i should say my car is a 1995 GTR R33 non-vspec.

What im after is decent response as its 90% a daily driver but still be good enough to shoot down the quater mile (if adel ever gets a bloody strip) in decent times. 11s.

Defiantly want over the 300kws mark but i guess not by to much.

Be able to have a fairly safe tune and still get those two above things.

These are the mods i have currently and dynos at 261kws -

Modifications:

Suspension New blisten Shocks, Lowered King Springs

Work XD9s 18 x 10 +18 with Kumo 275s all round

Kakimoto Catback Exhaust, Just Jap front pipe, high flow cat

700cc SARD injectors

TOMEI cam gears

HKS pods

Custom Cold Air Intake

Trust Intercooler

Nismo Fuel Pump

Power Fc and Controller

Greedy Profec 2 Boost Controller

Twin Plate Clutch

HKS boost gauge

Carbon Wing Blade

And these are the mods i am looking at getting to hopefully finish off my car to get out of it what i listed above -

2860r-5 Turbos

Bosch Z32 AFM's and plugs

Tomei Dump Pipes

any thing else i may need?

Would this set up get what im after?

Any ideas or suggestions?

Any help would be great as i dont want to go ahead and find out ive fallen short.....

cheers

Adam

Link to comment
https://www.sau.com.au/forums/topic/242050-33-gtr-finalising/
Share on other sites

yep, that will be a good package mate. the only thing I would add would be a nice oil cooler kit (get one that mounts in either the left or right duct in the front bumper, not the ones that mount in front of the radiator).

you could also consider nismo AFMs over the Z32s. no plug mod needed and no mod to your intake set-up either. they are basically a Z32 sensor in a standard casing.

fked if I know for sure, but for just over 300kw you want the smaller ones (I think the -7s). the other ones are more like a 2530 and will give 350-380rwkw and are more laggy.

-7s 300-330rwkw

-5s 360-400rwkw

You can run 11's on the stock turbos, so with -7/R31N1/GT-SS, you'll run 11's without a worry.

And yeah, Nismo AFM's.

Stock dumps are fine from what ive seen.

Im using them (250rwkw @ 12psi) and there are cars over 300rwkw with -7's using them also without issue and no noticeable performance issue.

I wish i had the coin to finish my setup for the full 20psi+ just to show that stock dumps can do it, overlap with a 'dump equipped' car and show there is no difference :)

ahhh cheers for that, ill start to look for -7sand nismo afms then instead. glad i asked now.. looking through the many pages just got a bit confusing for me lol...

and dumps.... i hear what your syaing... lol.... but id hate to find out later i should have had some. and seeing as ill have the turbos off and out i might just add them... lol u know just in case lol

my problem is tho and yes will sound stupid, but im not 100% sure what type to get as i have heard a few not being drop ins. Then you needed them grounded off new shimes etc etc etc

I just didnt want the hassel. But yer wouldnt mind a set

Cams again... debateable (more so than dumps)

IMO a set of cam gears properly dialled in, all you'll need

Yeah, agreed. While the lumpy idle is tough, it's completely unnecessary. There's a black R32 GT-R that I'm reasonably familiar with that runs ~370 RWKW on standard cams.... :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...