Jump to content
SAU Community

Recommended Posts

Before you start talking about 3g setup's you should probably say what the car is used for. Have you considered that the pads you have may not be right for your usage eg. track pads on a street car or street-low temp pads for a track car. Braided brake lines will also improve feel of the brake pedal and thus more responsive braking, slotted rotors will also increase braking. With these 3 things you are up to about $800-1000 and this will significantly improve your braking without changing your whole setup.

Edited by SLEEPR85

I wouldnt be talking bout doing it if it wasnt needed but its used mostly a daily but does a fair bit of high speed country driving and i also live in the adelaide hills, also want it for a few track days. Car has 290rwkw atm and after only a couple of decent slow downs brakes are hot and pedal starts feeling spongy. Standard brakes and pads atm.

Standard brakes and pads atm.

If i was you i'd try some decent pads and some good brake fluid then first before anything, stock pads are for stock power and handling. Spongy pedal feel is your stock brake lines heating up and expanding under the pressure, and as i said before braided lines will help this. Then if you still are not happy, then think about changing your calipers to something bigger. I'm running QFM K500 on my GTT at the moment and they do the job for my spirited hills drive. Also do a search man, theres heaps on this.

Also do a search man, theres heaps on this.

Not entirely true, info on F50 or BNR34 brakes is pretty limited....

However, I agree, before sloshing out 3k for an R34 setup, you should try getting some NISMO brake pads and braided lines.. Your pads will hold up to far greater forces and temperatures, the lines will also give you a better feel, as SLEEPR said, the lines WON'T expand and hence the middle pedal won't feel spongey and vauge.

Hey Bud,

I agree totally with the above.

I would assume your current pads are old, your fluid has been boiled or has water vapor in the lines.

I new set of pads Ferodo 2500's would be good and 4 dot fluid then see how you go.

at 260rwkw I feel I need to step up from the stock pads but they are pretty good if you ask me.

Check the group buy section for a disc rotor upgrade if you'd like to go all out

Has had brake fluid flush only a couple of months ago when it got serviced and new turbo added.

Have seen the group buy but was thinking about just going all out and not having to upgrade again if i get more power.

Does anyone know if the GTR brakes fit?

Your car isnt that old so there is probably little to be gained from upgradign to braided lines. Especially if down th etrack you may consider a new setup, your braided lines will most likley not be able to be used with the new setup.

But is pretty simple, check your brake rotor thicknesses, if they are healthy then get them slotted. Just buy some Endless CCX pads and get some Castrol SRF fluid in there. If that isnt enough braking capacity for your car then fair enough...you will most likely need bigger brakes.

Yes R34 GTR Brembos do bolt on. For around the same money your other options are G4 etc brakes which people seem to like especially for the price.

...i will add if you are frying GTT brakes with good fluid and pads on the street, you seriously need to look at how you are driving :P But seriously, you must be hitting some crazy speeds to fry the std gear so maybe best just slow it down a tad :D

Most of the time they are fine, but if i go for a burn around where i live in the hills when noone is around after about 5 mins and a few good hairpins that the brakes arent working as good as they should be, i should point out i only do it occasionally but do alot of open road country driving where i used to live and theres stuff all cops so i cruise at a fair speed and if i want to stop i want it done damn quick.

Thanks for the answers though guys, ill have to see what a set of GTRs are worth and weigh it up against slotted rotors. Can always sell the current setup and use the cash for bigger brakes.

http://www.k-sportracing.com/8pot-330x32-17-intro.html check these out and give me call if you are interested 02 99059523 ask for frank and we will look after you :D

Will you need an adaptor to run these calipers or will they bolt straight up?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...