Jump to content
SAU Community

Recommended Posts

  • Replies 452
  • Created
  • Last Reply

Top Posters In This Topic

Bike (deadly treadlys) riders who come up the left of you at a set of traffic lights and then angle them selves in front so your stuck behind them.

Quite patient with bike riders... Just that one where they blatantly obstruct traffic gets up my nose.

I've seen one bike rider at my local small roundabout moving faster than the cars flying up the inside. He attempted to squeeze past the car only to swear and carry on when he clips the gutter and stacks it as the car didn't see him flying up the inside. :S

Bigpond customer service. On the line for 2 hours the other night. Transfers around the globe and spoke with 5 different people; my issue never got resolved in the end. The bastard hung up on me.

I dont like pink shirts either.

Bigpond customer service. On the line for 2 hours the other night. Transfers around the globe and spoke with 5 different people; my issue never got resolved in the end. The bastard hung up on me.

Debt collection agencies ... when you've paid for the original invoice but they won't listen. :O

I got a bill from video/dvd hire shop for some overdue movies. Came to about $21. I paid the said bill on the due date, its come out of my bank account. Yet the tools instructed the collectors. :wub:

Debt collection agencies ... when you've paid for the original invoice but they won't listen. :banana:

I got a bill from video/dvd hire shop for some overdue movies. Came to about $21. I paid the said bill on the due date, its come out of my bank account. Yet the tools instructed the collectors. :blush:

+1. same things happening to me. f**kin annoying.

The useless f**ks at the transportsa places that have no idea what their doing.....I gave up with the new plates for now; too frustrating. :down:

I'm sure their job isn't easy but they could improve their attitude a bit.

/rant :spank:

Edited by Eddyfier

Contrary pricks, people that seem to argue just for the sake of it regardless of the facts at hand.

Judgemental people...You know the ones, they sit in judgement over all and sundry telling whoever will listen all about it.

When in reality they'd have difficulty telling the difference between an ass and an elbow.

those little yellow signs on the back of cars especially " BABY ON BOARD"...

Do i give a f**k you have a baby on board? what does that mean try even more not to crash into that particular car ffs

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...