Jump to content
SAU Community

Recommended Posts

Hello,

most of the topics here and in the Internet talk about how good a coilovers brand on a track. I'm worried about quality and reliability. that is due to difficulties and too high expenses to overhaul coilovers in the country I live in. actually, I'll have to ship overseas in order to get them fixed, and that costs a fortune.

I'm looking for a coilover set that will last long. I'll be using my car on normal streets, no track racing at all. sure I want to add some handling control and lower my car, but I mainly care about ride comfort, durability of the suspension, and hight and damper adjustability. my car is planned to have 650 whp after completing my project.

so, which brand you think better, or which brand you have experience with and is durable? and which spring rate?

HKS hipermax III, Tein, Zeal, Tanabe, Megan, Ksport, G4, D2, Silkroad, Bielstein, JC-Project, Croxx, Apexi, etc. you're most welcome to add any suggested brand among those.

your openions and recommendations are highly appreciated as decision to choose a brand got me in a whirlwind!

cheers,

Edited by evil angel
Teins are good and you can get them rebuilt easily also locally

rebuilt is not an option for me. I already have a set of old Teins, the two rears are done leaking all of the oil :thumbsup:

if I'll send the 4 shocks to Tein and get them overhauled, it might cost me more than AU $1,200 due to the shipping cost for a round trip. so, whats the point!! it's better to get a new set with new technology.

650hp and no track time!?!

That's a waste of a car. If it's street only go with the bilsteins in the group buy and save yourself a packet. You'll need the extra dough for that engine :D

no doubts mate, I'll have the power soon in my car, but I don't have a racing track to push that power on it.

ok, is there a group buying Bilstein? any link to that topic? I would like to take a look over the prices and possibility of shipping a set overseas to me. and by the way, where are bilsteins made at?

keep sharing yuor openions guys, I'd like to see what other options I have.

and hey, thank you all for passing by my topic and sharing your ideas. :)

I think I've seen that topic. I checked the latest replys and it seems that SK runs into huge back orders!! some of the members "as they posted" make the payment and waited for months !!

I'm located at Saudi Arabia.

Hi mate,

What's your budget? With the sh!t Aussie dollar at the moment a set of Aussie Made DMS Coilovers might be cheaper than you think... and you'd have them in weeks, not months. You want me to price you up a set with springs?

Cheers,

Greg

Hi mate,

What's your budget? With the sh!t Aussie dollar at the moment a set of Aussie Made DMS Coilovers might be cheaper than you think... and you'd have them in weeks, not months. You want me to price you up a set with springs?

Cheers,

Greg

Hi Greg,

how much would it cost? and how much time you think it'll last before leaking its oil? I mean, is it good quality for street useage?

cheers.

jetpilot1986 - if you wish to promote and try and drum up sales - you are required to become a paying trader of this forum.

You are clearly a business with sig advertising, in thread promotion and a email address linking to a business website.

Please cease from trying to drum up business until such a time as you are a paying trader

Thanks.

I think Bilsteins would be the way to go for durability. But for all round choice for you GTR i woudl grab some Tein Monoflex

Hi Roy,

did you put into considration that the car will be driven only on normal streets?

I mean, don't you think that Monoflex is more than what you would need on normal streets?

cheers,

Hey, we race an R33 GTS. it has plenty of HP.

We were running Tein Super street but have since change them to the MonFlex.

Very happy with the change and the lap times are down as a bit of proof....so if its track you want or hard/spirited driving...check out Tein Mono Flex

Perhaps, but i have been in plenty of cars with Super Streets and they are really ncie on the street, though still twin tube in design. The Monotube are obviouly monotube in design, and at the end of the day...it all comes down to seat of the pants preference.

With off the shelf Bilsteins they are great quality and to the liking of some/many, but they cannot be tweaked by the driver to suit your ride height desires and ride changes

I have Bilsteins FTW, dont waste your money on anything else- contact Elite Racing Developments-Dan or a Bilstein supplier in your neck of the woods- add Eibach springs to the mix- unbeatable combination

Hey, we race an R33 GTS. it has plenty of HP.

We were running Tein Super street but have since change them to the MonFlex.

Very happy with the change and the lap times are down as a bit of proof....so if its track you want or hard/spirited driving...check out Tein Mono Flex

hey mate,

would you please tell me waht springs rate you have on those monoflex? and how is the ride on pumpy streets?

how long you have them on your GTS?

Perhaps, but i have been in plenty of cars with Super Streets and they are really ncie on the street, though still twin tube in design. The Monotube are obviouly monotube in design, and at the end of the day...it all comes down to seat of the pants preference.

With off the shelf Bilsteins they are great quality and to the liking of some/many, but they cannot be tweaked by the driver to suit your ride height desires and ride changes

I would really appreciate a clarification about the difference between the twin tube and the monotube. which one is better, and used for which type of driving.

I have Bilsteins FTW, dont waste your money on anything else- contact Elite Racing Developments-Dan or a Bilstein supplier in your neck of the woods- add Eibach springs to the mix- unbeatable combination

hello,

if Bilstein is not hight adjustable, then it's out of my list. is the set you have hight adjustable?

the bilsteins are circlip height adjustable, its not as easy as threaded sleeve adjustment, but fine if u dont plan on changing height all the time. you can however put threaded sleeves on the bilsteins to make it easily height adjustable like any other coilover package.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...