Jump to content
SAU Community

Recommended Posts

hey guys..... now atm my r33 is dosing or fluttering (no BOV) the reason why is i have had to take my BOV off due to shit idle seeming im running a microtech lt12 and the idle adjustment suks pretty bad... plus my idle screw on my car doesnt work due to all pollution gear and all that is blocked up.....sooooo i have a high mounted t04e with a stainless intake pipe with a blitz pod and at 16 PSI it is freakin loud!!!!... so i was wondering at ways to rid of the loud flutter and wondering how to reduce it without reducing boost, putting on a BOV ect......

just for those that hate the sound.... so do i.. i mean it sounds cool but after a few kms with it it really getsa annoying ... soo guys could anyone chuck me ideas.... my only though is to either chuck back on a panel filter .but to a high mounted turbo?? thats weird.. or the only other way is to change ECU to somethin with idle control and chuck on a BOV..

thanks guys...NO IM NOT FULLY SICK EITHER..FAR FROM IT.. HAHA

Link to comment
https://www.sau.com.au/forums/topic/247998-stopping-dosing/
Share on other sites

just throw a well thought out plumb back BOV on it mate.

I took my BOV off, and my car started stalling, and sounding "fully sick"

Anyway, stock one back on, no more stalling, or loud bullshit noise.

Edited by The Mafia
Link to comment
https://www.sau.com.au/forums/topic/247998-stopping-dosing/#findComment-4304636
Share on other sites

just throw a well thought out plumb back BOV on it mate.

I took my BOV off, and my car started stalling, and sounding "fully sick"

Anyway, stock one back on, no more stalling, or loud bullshit noise.

ahhhhh... my only issue is that my cooler piping is far from stock...lol.... so how to i go about chucking a stock bov on??... do i need to cut and weld on a flange?? then also cut and weld a smaller cylinder for the return line of the plumb back??

if its a plumb back..not like my old turbosmart atmo.... that wont muck my idle around will it?? cause its feeding it back into the lines right??

thanks for ya reply man

Link to comment
https://www.sau.com.au/forums/topic/247998-stopping-dosing/#findComment-4304699
Share on other sites

ahhhhh... my only issue is that my cooler piping is far from stock...lol.... so how to i go about chucking a stock bov on??... do i need to cut and weld on a flange?? then also cut and weld a smaller cylinder for the return line of the plumb back??

if its a plumb back..not like my old turbosmart atmo.... that wont muck my idle around will it?? cause its feeding it back into the lines right??

thanks for ya reply man

I guess so.

Don't have to use a stock one, just a decent one I guess. And yeah, just plumb it back into the intake pipe pretty close to the turbo inlet

Link to comment
https://www.sau.com.au/forums/topic/247998-stopping-dosing/#findComment-4304716
Share on other sites

where was your bov that you took off?

what kind of bov was it?

most aftermarket ones have attachments that you can buy to make them plumback instead of trumpet.

then you just need to run a hose of some sort to the inlet (between filter and turbo).

what is the intake piping made of? I assume it's not the stock one since you have a high mounted AM turbo.

if it is some sort of metal, you could get an exhaust place to take it off and cut and weld an outlet for the bov return pipe.

Link to comment
https://www.sau.com.au/forums/topic/247998-stopping-dosing/#findComment-4305157
Share on other sites

i dont see what custom piping has to do with fitting a BOV

Pull a small section off, weld a fitting on, attach BOV - problem solved :thumbsup:

Im selling GTR BOV's too at the moment, best item for the job :D

+1 closer to the throttle body the better apparently to,

GTR ones are perfect untill you hit about 21psi after that I hit up a Plazmaman one, they do the plumback/trumpet interchangeable bovs which allow you to switch between plumb back and atmo.

Link to comment
https://www.sau.com.au/forums/topic/247998-stopping-dosing/#findComment-4305258
Share on other sites

thanks for the replies guys!!!!...awsome!!!!...... ahhh my old BOV spot is just to the throttle body side of the cooler... under or in the front bar if ya feel me... hidden :P :P so its gonne suck fitting a plumb back tube to it... ummm... my intake is make of stainless and has nothin on it... like just a dose pipe.... i think ill hold off just a bit until i fit a forward facing plenum... then fit a gtr and plumb it back :) :) i just want my performance but want rid of the sound... cause if cops pop up my hood.. uh oh ... 19yr p plater with 250rwkw car... done in fo sho..

once again cheers for those replies!!! handy as...

Link to comment
https://www.sau.com.au/forums/topic/247998-stopping-dosing/#findComment-4306374
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You'lll likely have to make do with R33 GTR for engine/tranny stuff, and Stagea for the body. I don't know that there's even been an actual diagram seen in the wild.
    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
×
×
  • Create New...