Jump to content
SAU Community

Recommended Posts

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Its just natural for the multi sensory experience to be appealing... i guess its a different case from person to person.... I like the sounds it makes, not because all my mates will hear it and think its fully sick, its just a pleasing sound for ME....if u dont like ur exhaust sound, get a silencer!

I agree with franks.

I elected a 3" straight through exhaust with a 3" tip. I told the exhaust shop I wanted it done to be as silent as they could make it.. Yes I knew it was going to be loud. I said this is why I kept the tip the same size, and opted for just a no frills stainless muffler, no rice cannon thanks.

The result? A very very smooth and powerful sound. It's definately, but loud in a powerful way. Like a european super car.

Not like those guys driving around in civics (and some with silvias) with 4.5" tips that sound and look like a milo tin rattling. Sounds like shite.

  • 3 months later...

Well after a 10 day wait in delivery (damn postman having a xmas holiday grrr) I replaced my HKS Pod filter with the standard airbox and a standard panel filter (came with it). Wasn't difficult to do but damn I can't wait till the new Snap-On tool set arrives, it'll make like so much more easier.

Ahhh sweet sounding RB25DET with no pod induction noises :P:):)

Under 3,500rpm it feels more responsive but over 3,500rpm i think its lacking power over the HKS Pod filter. I'm not in a great hurry to replace the standard panel filter with a K&N unless I can find 1 at the right price so i'll just see how fuel comsuption goes now with the standard paneil filter vs pod filter.

I've never had a pod but there was a bit of a difference once i put my K&N panel in... I'm getting a fmic on thursday and still keeping the factory box, i'll just be modding the factory snorkel as the piping will hit it :D

I've got a FMIC with the piping useing the standard holes in the corner, nothing needed to be modded on the stock airbox to make it fit.

I was looking into an fmic like that... i found one i liked but the piping was going to be lower than my front bar (which is very low) so the piping would hit the ground... so i have to got with the other style...

Ben, why didn't you just get a box for the pod?

I have the box from UAS (infact I've had it for 11mths and it cost me like $200). But I didn't like my Pod filter, too noisey and it needed modding just to fit in with my IC pipes. Also I didnt have a CAI for it so the only air it was getting was the dirty hot engine bay air.

The stock box makes the car such a pleasure to drive now. No wooshing or hissing sounds :D

Edit: Still have the UAS box here too so if anyone wants it PM me an offer :D

franks but u campared the stock airbox to an exposed pod in the engine bay tru? im sure a high quality oiled pod in airtight heat proof box wif a phat CAI would give more gains then both options, ive heard of people netting 10kw@ the wheels wif a custom box setup but i havent seen any proof

I dropped into my local AutoOne on the way home today and they sell the K&N Panel Filter for $109.95 and the Redline Panel Filter for $71.25

They had a K&N setup on a bench which consisted of a large perspex box with a hole cut in the front with the K&N Panel Filter connected to it. At the back (inside the box) was 2 massive 15cm electric fans sucking the air through the filter. A ping pong ball was in a plastic cylinder and the ball did not move no matter if the K&N Air Filter was in place or whether it was removed with no filter.

Excellent airflow if you ask me...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSP male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSP reducing bush?
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...