Jump to content
SAU Community

Recommended Posts

Hi guys,

Just thought I would throw in my 2c if that's ok:)

turbo cars are fitted with bovs that plumb back - this is something the manufacturer does, and for good reason (another story)

atmo BOV vent crank case gasses to the atmosphere - this is in direct contradtion of road traffic acts australia wide, and it also contravenes EPA reguations.

It took me a while to work out why atmo BOVs are illegal, until I was reading ADRs with regard to crank case gasses.

All vehicles manufactured after 197? (from memory) must burn crank case gasses through the cylinders as part of emissions control - this is where the problem lies, as under boost crank case gasses go into the intake after the afm and before the turbo (which is why we fit catch cans). Once we take out foot off the accelerator, those gasses vent to atmo.

Hope that clarifies.

As for noise, the only regulations I could find were on vehicle exhaust noise, as for removing a 'turbo whistle' OMFG how can you remove something that doesnt exist - should take him to court purely on the principle - like to see the copper produce a dictionary (or any other legitimate) definition of a 'turbo whistle'. If a defect notice is a legal document, shouldnt the issuing copper be under some sort of requirement to get his terminology right?

Should get a statement off a mechanic to the effect that there is no such thing as a turbo whistle, then go see the guys supervisor and make a complaint that you wasted time trying to remove something that doesnt exist:)

CRANK CASE GASSES are different form your bov gasses.

catch cans are used to stop- the amount of shitty blow by in your engine. mostly used for ****ed cars, or crazy high performance cars. bov's vent air that has come from your air filter, thru your turbo then thru the intercooler to your pipes.

there must be different laws in SA. as this is the Queensland section.

now listen. Atmo BOV are legal.so long as they comply to the noise and polution levels.

Where do the crank case gasses go when under boost?

All cars create blow by, whether only a little or alot. If you have a look at the two connectors on top of the rocker cover you will see that they go to the intake, after the AFM, as under boost the gasses cannot go into the plenum for obvious reasons, which is prevented by the PCV (positive crankcase ventilation) valve.

If the gasses did not go into the intake, or were vented to atmosphere, the crankcase could pressurise and cause all sorts of problems (like blowing gaskets and seals - not pretty)

It was only in the early seventies that cars started being required to comply with emissions standards, and the gasses could not longer be allowed to vent to atmosphere.

If the rest of you emissions control is correctly plumbed up, there is no physical way you can stop some crank case gasses getting into the charge air. It is this charge air that vents when the BOV lifts, hence atmo is not street legal.

The requirements for cars to comply with emissions standards are the same in every state.

  • 15 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..   
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...