Jump to content
SAU Community

Recommended Posts

Well title says it all....I used to read this mag a while back, have been into various newsagents over the past few months to buy a copy but it seems that no ones has it and from what I can tell the whole mag seems to have gone down the tube...

Anyone know anything, like if it is truly dead (and if so, how come?) or any other info...Links to news stories or anything would be tops...

Cheers

Link to comment
https://www.sau.com.au/forums/topic/248985-speed-magazinewhat-happened/
Share on other sites

Speed has been gone for ages, couple of years I think.

Correct. Towards the end of it's time, it was turning into quite a n OK read, but someone pulled the plug. Too soon, IMHO. It always has qual' photos, and even ran a shot of my car that came out trumps, even with a tough caption!

SP33D mag got buried because the publishers couldn't justify it. I think they were trying to aim it as a classier Autosalon mag with same great photography, reasonably well sorted cars, basic technical articles, but no skanks.

Unfortunately I think that the other ricer mags in the publisher's stable made the cut. Half dressed pre-teens draped all over candy painted cars sells magazines.

I didn't mind SP33D, and actually bought a fair few issues. It was less ricey and VD-ridden than Hot4s / AutoSalon / Freestyle etc but a lot lighter and more visually appealing than Zoom etc. For me, if they'd gotten their facts right more often and used a spell checker it would have been the perfect general "tuner" mag.

SP33D mag got buried because the publishers couldn't justify it. I think they were trying to aim it as a classier Autosalon mag with same great photography, reasonably well sorted cars, basic technical articles, but no skanks.

Unfortunately I think that the other ricer mags in the publisher's stable made the cut. Half dressed pre-teens draped all over candy painted cars sells magazines.

I didn't mind SP33D, and actually bought a fair few issues. It was less ricey and VD-ridden than Hot4s / AutoSalon / Freestyle etc but a lot lighter and more visually appealing than Zoom etc. For me, if they'd gotten their facts right more often and used a spell checker it would have been the perfect general "tuner" mag.

Yeah I agree with you on that one.

The articals were actually quite helpfull and the cars were actually decent, non of that hot 4's showpony bullshit.

I got the issues 1 to 4 and then was given issue 16 from memory, again was a good read with some helpfull tips.

Other than that I read HPI but I find they just give an over all / general idea of the cars and modifications.

That was 3 years ago, if not more...

Im pretty certain the last issue made had the SAU-Vic GOR Cruise featured in it... was 4 years now i think about it because my car was in it... and its been off the road for the past 3 years

Yep, died in '05 from memory. I should know though, my car was in the last issue :P

I have that issue, I recall I bought it for the write up on your car :D

Grab a copy of Tarmac magazine, only thing I buy nowadays... other than the odd copy of UK Top Gear mag

AWWWW wish I could say my car has been in a mag. lol.

but noooo.

I WISH!!!!! I WOULD SOOO LOVE IT.

lol

and now featuring a stock R32 and its performance is pretty darn.... ahh stock?

lol but it looks good.

Suppose it could be a "how stock can ya go" featured car...

like a limbo type context..

Or, just plain old "HOW TO BEAT THEM DEFECTS." lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...