Jump to content
SAU Community

Recommended Posts

  • Replies 99
  • Created
  • Last Reply

Top Posters In This Topic

what exhaust housing did you pick and why?

I didnt realise that this was an interview... I will post the turbo specs soon.

Bump also wondering if your using the stock exhaust manifold?

Yes I am using the standard manifold.

I didnt realise that this was an interview... I will post the turbo specs soon.

Yes I am using the standard manifold.

What star sign are you?

Do you like long walks on the beach and candle lit dinners?

Do you make love on a bed of frangipanis?

  • 1 month later...

Update:

Parts have arrived and I have spent quite a few days in the garage putting them all in :)

I love reading this on the side of the box (usually means there is something nice and shiny inside).

210120091150.jpg

Mmmm Trust front pipe... And split dump. :P

210120091153.jpg

210120091151.jpg

210120091152.jpg

Exedy Hyper single ceramic button... (flywheel machined too).

210120091155.jpg

Genuine Nissan water pump (had too many problems in the past with inferior water pumps).

220120091158.jpg

Gearbox and tailshaft ready to go back in... (Note the "custom" crossmember).

210120091156.jpg

Front of the motor - Naked! :)

220120091157.jpg

New water pump installed.

220120091160.jpg

Wastegate actuator mount and connector pin had to be modified to get them into the right position.

220120091159.jpg

All parts now installed, the next step is to make up a custom intake pipe for the turbo, replace all oils and fluids and then a dyno tune!

More pics to come (sorry Michele, still no Frangipani stickers) :P

Stay tuned.

Im hoping to have it running in the next 2 weeks, but it wont be driving on the road until its tuned and I have had a few other "goodies" installed :P

It should all be finished by the end of this month... Fingers crossed :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
×
×
  • Create New...