Jump to content
SAU Community

Recommended Posts

  • Replies 99
  • Created
  • Last Reply

Top Posters In This Topic

what exhaust housing did you pick and why?

I didnt realise that this was an interview... I will post the turbo specs soon.

Bump also wondering if your using the stock exhaust manifold?

Yes I am using the standard manifold.

I didnt realise that this was an interview... I will post the turbo specs soon.

Yes I am using the standard manifold.

What star sign are you?

Do you like long walks on the beach and candle lit dinners?

Do you make love on a bed of frangipanis?

  • 1 month later...

Update:

Parts have arrived and I have spent quite a few days in the garage putting them all in :)

I love reading this on the side of the box (usually means there is something nice and shiny inside).

210120091150.jpg

Mmmm Trust front pipe... And split dump. :P

210120091153.jpg

210120091151.jpg

210120091152.jpg

Exedy Hyper single ceramic button... (flywheel machined too).

210120091155.jpg

Genuine Nissan water pump (had too many problems in the past with inferior water pumps).

220120091158.jpg

Gearbox and tailshaft ready to go back in... (Note the "custom" crossmember).

210120091156.jpg

Front of the motor - Naked! :)

220120091157.jpg

New water pump installed.

220120091160.jpg

Wastegate actuator mount and connector pin had to be modified to get them into the right position.

220120091159.jpg

All parts now installed, the next step is to make up a custom intake pipe for the turbo, replace all oils and fluids and then a dyno tune!

More pics to come (sorry Michele, still no Frangipani stickers) :P

Stay tuned.

Im hoping to have it running in the next 2 weeks, but it wont be driving on the road until its tuned and I have had a few other "goodies" installed :P

It should all be finished by the end of this month... Fingers crossed :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
    • Pretty sure it is a common fault. I believe this is the only part you need, but don't quote me as I don't have a V36.  I also believe it is a bit of a pain to change and the device needs to be encoded to the car once it is replaced, so may need someone with the right tools. Buy Genuine Nissan 48700JF00D (48700-JF00D) Lock Set-Steering. Prices, fast shipping, photos, weight - Amayama
    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
×
×
  • Create New...