Jump to content
SAU Community

Recommended Posts

Has anyone had any isues with the tensioner pulley or belt rubbing on the cam gear cover or lower belt cover going from the 30 build manual? It suggests mocking it up but that would be a lot easier said than done. I gather the general opinion seems to be setting the pulley out a further 1mm than the manual suggests so you get more movement on the tensioner.

Any info please..

Edited by leeroy_25

I have been looking at this issue. I was going to ask the same question. Do you guys bother trying to 'cover' the idler, or just leave it hanging in free air? how does the belt go with road grime and stuff?

cheers

Thanks All!

Hole is in my block now so fingers crossed! I have looked at some other blocks and some seem to have some very different hole positions.. I am guessing it's not really thqt critical within reason as the tensioner has a fair bit of adjustment.

Hey Al, Nice looking motor! Looking at you turbo oil feed line (unless it's the water one?).. Are you running a series 1 block by any chance? If so would be interested to see what you did about oil and water feeds? I was planning on getting my oil feed from the pressure switch. and draining to the sump.. water is easy enough to put in where it belongs!

Any more pic of your build?

Cheers

Lee

psi: The plate is only held in by two existing bolts, so it's really easy/quick to take off. Not sure why you would need/want a hole for adjustment anyway; once the belt is fitted and properly tensioned you wouldn't need to adjust it again.

Thanks All!

Hole is in my block now so fingers crossed! I have looked at some other blocks and some seem to have some very different hole positions.. I am guessing it's not really thqt critical within reason as the tensioner has a fair bit of adjustment.

Hey Al, Nice looking motor! Looking at you turbo oil feed line (unless it's the water one?).. Are you running a series 1 block by any chance? If so would be interested to see what you did about oil and water feeds? I was planning on getting my oil feed from the pressure switch. and draining to the sump.. water is easy enough to put in where it belongs!

Any more pic of your build?

Cheers

Lee

Thanks Lee.

Pretty sure it's a S2 motor.

Few more angles of the engine on the stand, not sure if you wanted to see any other pics; like the pistons, head porting, engine bay prep and completed engine bay, etc.

post-1811-1229783590_thumb.jpg

post-1811-1229783712_thumb.jpg

post-1811-1229784255_thumb.jpg

Nice pics!!

That does nicely thank you! What's the external oil filter housing part in the third pic?? Is that for an external pump or something?

What spec you got and what power are you hoping to get?

Cheers

Lee

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...