Jump to content
SAU Community

Recommended Posts

Hey guys...

Yes I have searched but came to no help...

So, I have a 96 R33 just with basic mods, stock turbo, cooler, exhuast, Powerfc. It has a alimighty rapid miss fire. It only happens when i have my foot flat and go over about 4500rpm, Say you put your foot down quater the way down it can rev right up same if you just give it a rev under no load... What I have changed are the coils (Superspark), tryed two sets of spark plugs gapped to .8, changed fuel filter. It doesnt happen all the time but atm everytime I drive it. I can see in the engine bay that there is a earth strap near the turbo that is broken so i measered the Ohms between the engine and the chassis and it seemed alright. so if anyone could help it would be great i have taken it to a workshop and they where pretty hopeless (Well known workshop to).

Cheers Matt

Link to comment
https://www.sau.com.au/forums/topic/249618-rb25det-rapid-miss-fire/
Share on other sites

Alright just a few more things i have found out today well when it missfires the engine light turns on I played around turning different warnings on and off, in the powerfc and it seems to be the knock sensor... The car is running rich blowing black smoke when the mis happens and you can smell it... Could it be a faulty knock sensor which is casuing it to run rich would this casue the miss or is my idea totally wrong?? Anways any help would be great

Cheers

What's the knock count on the Power FC read when the engine light comes on? It's most likely just pinging its head off, safest bet take it to a workshop to check the timing and AFR's over 4000rpm, most likely leaning out a bit up top.

Didn't run some crap fuel in it recently?

Edited by PM-R33

Had good fuel in it have been threw a couple of tanks. The knock count is high when the engine light comes on but the miss doesnt happen when the light comes on only happens above 4000rpm with foot flat, So I dont know if im chasing two problems now. Can you pick a new coil pack loom anywhere or is there only second hand ones?? and workshop wise around Brisbane what can you recommened?? I had a bad run with the workshop last time over a few little things where it got tuned, like cross threading spark plugs and not telling me and letting me find out the hard way

Hmmm sounds like two seperate problems, a missfire problem and a knocking problem.

For the knocking its going to be in the tune.

As for the missfire, if you have changed plugs (BCPR6E's?) and it still does it, then most likely it is the coilpacks or the loom.

As for the broken engine earth, there is still a main engine earth on the block underneath the plenum, however i would still add a couple more earths off of the head. I picked up a Pivot engine earth/voltage stabilizer kit for $50 brand new to test it out (retails for $300 on nengun at the moment, f**k that!) and straight away noticed the car was easier to start and the voltage didn't drop down as low on start up anymore. So extra earthing of the engine definetely helps a tiny bit. Add another earth near the coilpacks to the body of the car just in case, it can't hurt.

Edited by PM-R33
  • 1 month later...

yeah im having this same problem too. ive had problems with splitfires though. ive had to send three back so far. had car running perfect again after sending back splitfires when i went over seas. just got back after 14months, useless brother wasnt starting it up every few days so pretty much sat there for over a year.

then they started it up just before i got back and it was running terribly so took out my wolf3d and put stock ecu back in. would run ok but miss fire at 4500rpm. so i figure its another splitfire coil pack. think i may have received a dodgey batch or something considering its the 4th one to die.

put the wolf back in so it ran ruff unplugged each coil to see which one made no difference. this is how i diagnosed last three times, replaced with a stock one and ran fine again.

this time thought it was the 5th one, changed for stock one, runs ok at idle now but still mis fires at 4500. so put stock ecu in again but still the same.

has gotten worse now sometimes doesnt even idle with stock ecu now. and can missfire anywhere through the revs as low as 2500rpm. seems to come and go with the missfire at idle but at 4500 does it everytime

not sure how to solve this one. possibly two coil packs gone at same time??? wiring loom? tried to search for "how to test coil packs" but couldnt really find an answer. any suggestions?

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Food for thought, the stock oil filter thread is a 3/4-16 UNF, which has an ID of about 10 to 12mm (according to ChatGPT lol). Now compare than to an 10AN, which has an ID of about 14mm (Raceworks is 14.2mm, Speed flow is 14.27mm).  
    • Yep, totally get that. However hooking in for Generator back up is only a few hundred bucks for the wiring. You could put a couple of those in (for different circuits explicitly) and run a couple of baby generators. Bonus, you can balance them across different circuits, and now have backups in your backup. I'm looking at buying places that won't even have water etc, and I don't mind the idea of getting off the electric grid either, even with everything you've said. This country already has enough power outages that even the mains grid isn't that reliable anymore. I do agree though on spending a bit more to get better gear, and to add some extra redundancy in to the system too.
    • You can set hard reserves on your battery system, and it can't be discharged past that.  
    • That sounds like an excellent idea. But total self-sufficiency means exactly that. You have no-one else to blame when your system faults out and you have no power for a week or two while it gets fixed. You'd have to go the whole hog and get a diesel genny and all the switchover gear, to get you through such times. And, despite the fact that over 20 years, my system has been pretty reliable**, I have seen so many inverter explosions (or less dramatic deaths), panel and roof JB fires, and so on, over that time, to know that the stuff is the same as any other bulk Chinese manufactured stuff. The failure rate is well above zero - both on the equipment and on behalf of the meth addled installation labour force. And then..... warranty and means of redress against the supplier you bought the gear from. Best I can tell is that only a handful of solar companies are still around within 5 years of starting their advertising pitch. They disappear and phoenix like crazy. So, as per 1st paragraph, I suspect the only way to is go balls deep and spend maybe 2-3 times as much as you might think, so that you have every base covered. Plus, know and understand your gear intimately, so you can diagnose problems, sort them out yourself, etc, etc. Plus, probably have to consider upgrading various parts as the years pass, to maintain compatibility with newer stuff, performance and reliability, etc, etc. Whereas, remaining attached to the grid has an ongoing cost that keeps going up even if you use bugger all power from it. But it does provide the fallback in case of the worst case with your own gear. You either pay up front or as you go, I suspect.
    • Add more solar panels to the array. Call the electricity company and tell them you're moving out... Live off grid electric wise
×
×
  • Create New...