Jump to content
SAU Community

Installing Greddy Profec B

usmair

By usmair,
in Engines & Forced Induction

 Share

Recommended Posts

usmair Mentor

usmair

Posted
Posted

Hey guys,

I'm installing the profec B but i need to confirm whether the piping from the "NO" port actually goes into the intercooler piping

at the moment its running to some sort of breather pipe for the POD.

I've also got a Greddy Spec M Intercooler so the piping is not all standard.

me and my mates think that we need to run the pipe from the "NO" port to the intercooler piping but we cant find a nipple on the pipe to hook it up too..

Do i need to go to a tuner shop and get a pipe welded on??

here is a pik of how it is currently set up

post-44179-1230541149_thumb.jpg

post-44179-1230541178_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/250481-installing-greddy-profec-b/
Share on other sites
usmair Mentor

usmair

Posted
  • Author
Posted

yeh originally i did have mine tee'd with the fuel pressure regulator but the car would not run more than standard boost no matter what i did with the settings on the controller...

the fuel pressure regulator was also tee'd to run the pipe into the back of the boost controller...

seems like its hooked up properly but i still cant figure out why its running the standard settings :S

usmair Mentor

usmair

Posted
  • Author
Posted

i was just reading some of the old threads and came accross something that i might try

am i suppose to remove the plastic bung from the NC outlet on the solenoid...

mine is internally gated so i just left the plastic thingi on...

JMW Mentor

JMW

Posted
Posted

Going by your pic's

Block the hose off going back to your pod

Tee the fpr line and run it to the 'NO' port on the solenoid

Run the line from the 'CON' port to the wastegate actuator diaphragm

Use the factory boost guage pick-up point on the back of the manifold, place filter inline and run hose to control module in cabin

Hope this clears it up a little :spank:

JMW Mentor

JMW

Posted
Posted

and best place to run the hose to the control module i found was through the grommet in the passenger side of the fire wall, just be careful not to stab any other wiring.

Good luck and happy boosting!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      "Cheap" bolt on turbo on RB25DET NEO

      By MBS206 · Posted

      HyperGear. Just get a high flow of the stocker. Good, reliable, and should bolt on. Yes it will want things like a retune once done, so you need to factor this in to your spend too.
    • Kapr
      "Cheap" bolt on turbo on RB25DET NEO

      By Kapr · Posted

      Hi. Iam looking for some "cheaper" bolt on turbo on RB25DET NEO. I do not want "big" power just better reliability than the stock turbo which is "fot now" good but is old and i do not think it has "easy" life. One the Skyline here running some "temu" china Turbo but i dont trust those... Thanks!  
    • Piggaz
      R33 GTR OEM parts + random parts and oils

      By Piggaz · Posted

      Hi guys, Making some space/cleaning up. A whole heap of random OEM R33 GTR parts and other random bits and bobs. I will update this thread as I go. Parts are located in Moorebank NSW 2170. Pickup preferred but will post at buyers expense. Prices are negotiable. If they don’t sell it will go in the bin. Item 1: BOV return pipe. $40 Item 2: RB26 cam gears. $20 Item 3: R33 GTR torque split, oil temp, boost centre gauge. $100 Item 4: RB26 fuel rail x 2. $20 each Item 5: RB26 Recirc valves. $50 Item 6: OEM upper front arms. $20 Item 7: Royal Purple Max Gear 75w-140 1 quart/946 ml x 5. $50 each or 5 for $200. Item 8: OS Giken 80w-250 diff oil 1 litre. $25 Item 9 Eibach springs. ers-11-140-60-0140. $100 https://www.streetfx.com.au/eib140-60-0060-eibach-ers-140mm-length-x-60mm-id-coil-over-spring?_ga_campaignid=22235933977&_ga_adgroupid=180146800292&_ga_keyword=&_ga_device=m&_ga_target=pla-295238231169&_ga_locint=&_ga_locphy=9071723&_ga_matchtype=&_ga_network=g&_ga_device=m&_ga_placement=&_gcl_id=CjwKCAjwlt7GBhAvEiwAKal0cvkVE_hstv24cDiaICsIk1oznH9zAoJf3By6vR3Tpe7jmByqM6JFHBoCZYAQAvD_BwE&gad_source=1&gad_campaignid=22235933977&gbraid=0AAAAADPiTbo1xAuvnjIWWYnezivf-BUSY&gclid=CjwKCAjwlt7GBhAvEiwAKal0cvkVE_hstv24cDiaICsIk1oznH9zAoJf3By6vR3Tpe7jmByqM6JFHBoCZYAQAvD_BwE    
    • MBS206
      remote oil cooler hose size, 8,10 or an12?

      By MBS206 · Posted

      That's kind of what I was getting at saying you'd be here soon regarding length etc being able to add additional restriction.  My assumption (possible donkeys of you and mption) is that the length of hose to an oil cooler, and back, isn't going to be that huge of a loss. Typically you're talking about 1.5m of total length. And so far everyone in our world hasn't had issues with oil not being able to get to a cooler and back, it's more been, how the heck do we get the oil out of the head and back down to the bottom? I'd nearly hazard a guess the biggest issue people have with oil cooling and oil supply, is being able to get the heat out at the cooler itself (not enough air flow, too small of a cooler etc) Also, when people mount them wrong and make really awesome air traps so they've dramatically diminished the cooling capacity.
    • GTSBoy
      remote oil cooler hose size, 8,10 or an12?

      By GTSBoy · Posted

      I will rebutt this and the preceding point from Dose....but without doing any calcs to demonstrate anything and without knowing that I am right or wrong. But... The flow capacity of a fluid transfer system is not limited by the smallest orifice or section of conduit in that system, unless it is drastically smaller than the rest of the system. OK, I use the word drastically perhaps with too much emphasis, but let's drill down on what I really mean. The flow capacity of the system is the result of the sum of the restrictions of the entire system. So, to make an extreme example, if you have a network with 3" pipe everywhere (and let's say a total length of only a few metres) and that 12mm ID restriction of the oil filter connection being the obvious restriction, then for any given amount of pressure available, the vast majority of all the pressure drop in the system is going to occur in the 12mm restriction. But.... increase the length of the 3" pipeline to, say 1000m, and suddenly the pipe pressure loss will likely add up to either be in the same order of magnitude, possibly even exceeding that of the 12mm restriction. Now the 12mm restriction starts to matter less. Translate this to the actual engine, actual oil cooler hose sizing, etc etc, and perhaps: The pressure loss caused by flowing through the narrow section (being the 12mm oil filter port, and perhaps any internal engine oil flow pathways associated with it) is a certain number. The pressure loss through, say, -12 hoses out to the cooler and back is negligible, but The pressure loss through -10 hoses out to the cooler, at the exact same length as the above, starts to become a decent fraction of the loss through the 12mm stuff at the filter port. Maybe even it starts to exceed it. I could actually do these calcs if I knew 1) how much oil was actually flowing in the line, 2) gave enough of a f**k to do things that I hate doing for work, voluntarily for a hypothetical discussion. Anyway - I reiterate. It's not the narrowest port that necessarily determines how much it can all flow. It is the sum. A long enough length of seemingly fat enough pipe can still cause more loss than a semmingly dominant small bore restriction.
×
×
  • Create New...