Jump to content
SAU Community

Recommended Posts

having a cut power cut out issues with my 32 and i suspect either stuffed spark plugs or coil packs but of course gona try the sparks as i haven't changed them since i got the car back in may :action-smiley-069:. car is totally stock except for cat back and pod and running stock boost.

went to super cheap and asked for some and he recomended me the ngk coppers. i have read that they are a good plug but have a short lifespan. will these be suited to the car anyway?

plus i don't change the spark plugs myself so i want to get iridiums because i have heard they have a longer lifespan which would be ideal for me when servicing.

iridiums are like $20 at super cheap though and i reckon a rip off. went to repco and the guy said that ngk state the double platinums were best suited to the rb20? quoted me $110. does that sound liek a good price? he told me it was trade price?

so i pretty much just want to know what would be best suited and i think the iridiums are yeh?

can some one tell me where to get a set for a good price? i think kudos motorsport has the best price around at the moment.

let me know. thanks!

Link to comment
https://www.sau.com.au/forums/topic/250785-need-spark-plugs-to-suit-my-32-gtst/
Share on other sites

The coppers you should use would be BCPR6E. They're heat range 6 and pre-gapped to .8mm which is what you want. The only downside is that you'll have to change them out about every 10thou.

If you go Iridiums, get the same, heat range 6 and pre-gapped to .8mm because you shouldn't re-gap iridiums as it takes the coating off and shortens their life dramatically. So don't buy the 1.1mm iridium.

Iridiums are good for low servicing periods. But some will say just use coppers. I've found my iridiums to be fine so far (at least 35thou now).

But if plugs don't fix your problem.....looks like coilpacks will need to be changed.

Edited by KeyMaker

some people say you get better power from the copper plugs also.

they really aren't hard to change..

just dont over tighten them.

i would try changing the igniter box before changing coils if the plugs dont fix your problem..

hmm so coppers would be good for about 10,000kms? if thats the case i'll just do the coppers then cause they are on special at super cheap for 4.15 a plug lol.

although the guy at supercheap told me 4,000-5,000kms? can someone confirm?

Edited by jakez88

depends on your boost levels.

you should get 10,000

although i only got 500km out of my last set.

i have bigger problems though..

I'm looking at getting a set of brisk plugs.

www.brisksparkplugs.com.au

heaps of tuning problems.

and ignition problems.

bresciani racing tuned my microtech and done an absolute c unt of a job.

now i have lost faith in the workshops as they charge you an arm AND a leg, then do a shotty job anyway..

so i'm sorting through the problems myself.

If you want something done right do it yourself hey.

I've got a CRD tuned Microtech (previous owner's choice not mine) and it overfuels like a pig - even with splitfires, if I don't change my plugs religiously every 5000km it starts missing due to carbon fouling.

There was another thread about plugs at one point - the consensus was if you've got a reletively stock car Iridiums can be a good choice (the set in my VN have done 80 000km and 3 years fine) but if you're running higher boost then they will degrade quickly, as will coppers, but they are a lot cheaper.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...