Jump to content
SAU Community

Recommended Posts

The hicas light stays on occasionally, after i start the car. If I turn the car off and on again, it goes away.

It's happened maybe 6 times now, in the last 3 weeks.

It never comes on after start up, while driving.

When its on, theres no issue with steering etc. Car drives normally. So i'm guessing some sort of wiring fault with the light, or a switch?

Any tips or known issues to look for here?

The power steering fluid was on the low mark when i checked, so i topped it up, but that wasnt it.

My hicas is intact, and i have no issue with it. So the lock bar suggestion isnt what i'm looking for.

cheers

Edited by Munkyb0y
Link to comment
https://www.sau.com.au/forums/topic/251550-hicas-light-r33/
Share on other sites

  • 5 weeks later...

ive tried getting into hicas diag mode. no luck.

can someone spell out the procedure for me?

this is what i tried.

start engine

turn wheel left then right 20deg 5 times (i tried 6 times too)

press brake pedal 5 times (tried 6 times too)

then i read somewhere, a faulty steering posiition sensor will prevent entering diag mode

if i have the procedure correct, i need some info on the steering position sensor. ie. how to get to it, and remove/replace, or test.

if i have the procedure wrong, slap me, and show me the way

cheers

Link to comment
https://www.sau.com.au/forums/topic/251550-hicas-light-r33/#findComment-4411494
Share on other sites

the day i removed my hicas was NOT a day i look back fondly upon!

make sure you have a good couple of hours... its kinda tricky to get happening the first time

Dont listen to him :) It is a simple job and if your on a hoist will take about 40-50 mins max. And i even had to drop the rear muffler to get at one side.

Use the guide on SAU and its a piece of piss. Even easier if you have a mate helping.

Link to comment
https://www.sau.com.au/forums/topic/251550-hicas-light-r33/#findComment-4412820
Share on other sites

I had this same problem, I ended up ditching hicas but before I did I found that just disconnecting, cleaning and replugging in ALL the wiring plugs to do with steering and hicas stopped it from happening. I couldnt trace it to just one connection.

Link to comment
https://www.sau.com.au/forums/topic/251550-hicas-light-r33/#findComment-4412823
Share on other sites

i've read conflicting reports on r33 lockbar installs.

what i want to know is....

does it affect the progressive power steering? i.e. does your steering still remain lighter at low speeds, firmer at higher speeds?

or is that lost, and you get heavier steering all time when you fit a lockbar

edit: is the steering position sensor used for anything besides hicas? does it need to work?

Edited by Munkyb0y
Link to comment
https://www.sau.com.au/forums/topic/251550-hicas-light-r33/#findComment-4412954
Share on other sites

so far i havnt even noticed a difference in the steering with the lockbar.

No noticeable change in heavyness at low speeds etc etc so couldnt comment. Im taking it to the track on tuesday. 1st trackday without it so ill let you know if it was much different to with it in.

Daily driving tho.. hasnt seemed to effect much

Link to comment
https://www.sau.com.au/forums/topic/251550-hicas-light-r33/#findComment-4414095
Share on other sites

Yup yup. Leave the computer where it is and just remove the globe.

The track (just got home) was amazing.

I wish id put the lock bar in sooner. Coming out of corners a bit quick and having the ass step out is so much more controllable! I was just stomping on it in 3rd and "power sliding" haha. With the Hicas i was getting thrown all over the place.

I got a couple of vids of some minor skids ill link when theyre uploaded. But the best ones were at the end of the track that there was nowhere to video from :huh:

So, go DO IT DO IT!!

Link to comment
https://www.sau.com.au/forums/topic/251550-hicas-light-r33/#findComment-4419946
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...