Jump to content
SAU Community

Recommended Posts

A message to all modified skyline owners in victoria, yesterday i got pulled over by cops and was slapped a defect on my skyline in the CBD. Funny thing is I had 3.5 inch exhaust system with a 5 inch tip, Nismo 400R bodykit, lowered springs, BOV, airfilter, 2 HKS pillar mount gauges, Microtech computer with handset (when caught) and the works etc.

I managed to talk my way out of it and was only defected by a "LOOSE HANDBRAKE LEVER" and need to get a RWC done.

PART 2 was RWC was done by a dodgy mechanic, so I took it to VIC ROADS, they didnt even bother to check my car! STAMP-FREE to GO! so whaddaya think guys? Also I heard that cops and on the prowl for modified cars, so beware!

Link to comment
https://www.sau.com.au/forums/topic/25193-defected/
Share on other sites

Odd, from the outside my ride would look the same as yours.

Lowered, 400r kit but without modded exhaust.

I have been eyeballed by lots of cops and not pulled over once.

I spose whenever they see me I'm adhering to the traffic laws and not driving erractically.

Maybe my car doesn't look like a "hoons" car. :)

Link to comment
https://www.sau.com.au/forums/topic/25193-defected/#findComment-535977
Share on other sites

Originally posted by Jamezilla

Maybe it's not the car they're checking Ed - maybe it's you?

That bad-boy image will catch up with you sooner or later :)

HaHa, posting in relay here Jimbo.

I don't have a bad boy image, you know that. I have absolutely no interest at all in Louise's young friends.

Whatever you heard, I had nothing to do with any of it.

:)

Link to comment
https://www.sau.com.au/forums/topic/25193-defected/#findComment-536391
Share on other sites

defection is nothing.

it comes with a modified car.

and the little 'dodgy-RWC' comment i wouldn't talk about that here.

And when we (i) organise cruises we have nothing to worry about. We've never had problems so relax.

Link to comment
https://www.sau.com.au/forums/topic/25193-defected/#findComment-536595
Share on other sites

Just got done in Fitzroy street.

BOV, should be easy to fix

Exhaust to low, hopefully the TEIN suspension, i can raise it

Nardi Steering wheel, no centre pad, (will have to check into this)

Front end to be aligned, although the tyres passed.

The last 2 are interesting ones, he said just get an alignment.

Link to comment
https://www.sau.com.au/forums/topic/25193-defected/#findComment-538338
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...