Jump to content
SAU Community

Recommended Posts

hmmm i got 294 hp running a HKS 2535 pumping out 17 psi on my R33 would there be a problem?

they said they max out at like 400hp so it sounds like you would be sweet

i'v got one on the way and i would only be pushing like hopefully 260rwhp when im finished getting everything i need so i should be sweet to hey

my mates soarer made 440rwhp on dyno with one walbro 255 and no problem in past 3 years.

In america the yanks (mostly supras and gto's, etc) absolutely love the walbros and dont even bother with bosch, these are big hp and big budget cars, they use like 4 walbros intank rather than going bosch or anything else. These guys run big workshops and swear by walbro on every car so why the bad name around here? Dont buy cheap ebay copy shit ones and you might be suprised :(

i used to love the walbro's but after having a spate of them unable to crack 200rwkw latley (last november) i have been sworn against them, 3 were bought from a large victorian speed shop and the other 2 from tweak it (probably all the same batch)

fitting 040's fixed the issue on all 5 cars.

Edited by URAS

Most people here on Okinawa run Walbro's with no problems. I have twin walbro's in tank and have had no problems for over a year now, and I ran a single one at over 400rwhp a couple of years prior to that. That pump is still in the tank along with another one. There has been a rash of the fake ones popping up though. A lot of reputable dealers get them to distribute and don't even know they are fakes from what I've heard.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...