Jump to content
SAU Community

Recommended Posts

Hi everyone! had nistune installed onto my r34 (Neo engine) with auto tranny and the dyno results showed 233hp (12 psi)at the wheels.

I have stock turbo and engine, 3in exhaust with 3.5 catback to cannon. FMIC, air filter, EBC, custom oiler cooler and radiator, HKS BOV. Now after seeing everyone's postings on their dyno results, im thinking is my results too little?? 233hp whereas similar setup, the other guuys are getting at least 210rwkw. Im not sure if there is anything wrong

2ndly: My aim is about 400hp atw and I am going overseas where I will be able to get my hands on parts at a relatively cheaper price so wanna get some advice on what parts i should get. Roughly, im getting a upgrade on my injectors(500cc or 600cc?), fuel pump (bosch 044) and a GT-RS turbo. is there any other recommendations from you guys on what i should get to achieve that aim? Reliability is my top priority as it is my daily car. :cheers:

Link to comment
https://www.sau.com.au/forums/topic/252117-dyno-result-normal-or-too-little/
Share on other sites

boost peaks at 12psi cos i have been reading alot that for the stock turbo, the safe tune would be at 12 psi. did thought of pushing it to 14psi but wouldnt want the turbo to die on me too soon thus had it at 12 psi. you reckon its safe to have it at 14 psi? but i dun thrash the car all the time by the way.

^^

yeah he said he had a nistune remap.

Sounds about right, i've got a 34 neo with nistune, split/dump, stock turbo with r32 actuator set at 10psi and getting around 170rwkw. It's begging for more boost though.

200rwkw @ 12psi is where it should be. +/- 15rwkw for dyno differences and you really aren't too far away from there and you are running through an Auto so sounds spot on overall

Best way to tell is at a dyno day really, everyone on the same dyno, same day is the only real decent way of telling if your tune is low on power easily.

You can compare maps/timing and so on but each car is different so it become tricky.

As for 400rwhp/300rwkw, a GT-RS really isnt going to get to that. I think there was one or two cars that made that figure and no-one elese has come close so probably high figures as most seem to make closer to 260-270rwkw which is about the limit i'd push a stock motor anyhow.

Plenty of threads on 250/270/300rwkw setups, so have a search around

well, could be the auto box losing another 10-15hp for me. well, after spending on the nistune and ebc, i really was expecting about 240 hp. (215hp prior to installation but has a really shitty AFR) 180kw was a tad little disappointing. but oh well, since im not too far away, i shall keep working towards it. will be getting another turbo, injectors and fuel pump when i go for my hols in feb. will see how it goes. but shd be getting a high flow cat next week. will scan the dyno paper tomorrow at work and let you guys have a look.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Try looking at Eibacb/H&R springs Thats what Gary sourced for mine.
    • Hey y'all! I'm curious about how y'all go about widebodying your cars. I noticed that when running a square setup, my front wheels are a bit more tucked in than my rear wheels. Not by much, maybe 5-10mm. This leads me to wonder - when I widebody, should I use narrower front flares and wider rear flares? I found a set of 40mm rear flares that I really like, and was thinking of pairing them with some 18mm front flares, but I don't want the car to look strange. How have others done this? Note, I'm in a sedan. Thanks!
    • And if it was anything other than an auto tranny part, it might be a problem. But seeing as all auto trannies belong in the recycling bin, it's fine.
    • I have an R32 Fenix rad. It is good.
    • All the schemas I can see, indicate your typical setup of ATF 'cooler' (read: heat exchanger) in the bottom radiator tank..ie; https://nissan.epc-data.com/stagea/wgnc34/5413-rb25det/engine/214/ ...but I can prattle on a bit here. These trannies have a thermistor in the sump ~ the TCU reads this and 1. bumps the line pressure up when the ATF is 'cold' and 2. prevents the TC lockup clutch from operating, until the ATF comes up to minimum operating temp (keeps the ATF 'churning' through the TC so it heats up quicker) -- trigger point is around 55C. In these conditions, the engine coolant temperature rises faster than the ATF temperature, and also helps heat the ATF up, which is why it's best to think of the in radiator tank setup as a heat exchanger ; the heat can flow in both directions... ...with these trannies, the 'hot' ATF comes out the front banjo bolt, flows through the cooler/heat exchanger, and returns to the box  via the rear banjo bolt. This gets a mention, due to the wildly different opinions wrt running auto trans fluid coolers ~ do you bypass the in radiator tank altogether, or put the cooler inline with the in radiator tank system...and then, do you put the additional cooler before of after the in radiator tank system?... ....fact is the nominal engine operating temp (roughly 75C), happens to be the ideal temperature for the ATF used in these trannies as well (no surprises there), so for the in radiator tank system to actually 'cool' the ATF, the ATF temp has to be hotter than that...lets say 100C -- you've got 25C of 'excess' heat, (slowly) pumping into the 75C coolant. This part of the equation changes drastically, when you've got 100C ATF flowing through an air cooled radiator ; you can move a lot more excess heat, faster ~ it is possible to cool the ATF 'too much' as it were...(climate matters a lot)... ...in an 'ideal' setup, what you're really trying to control here, is flash heating of the ATF, primarily produced by the TC interface. In a perfect world, wrt auto trans oil cooling, you want a dedicated trans cooler with builtin thermostatic valving - they exist. These should be run inline and before the in radiator tank system ~ when 'cold' the valving bypasses the fin stack, allowing the ATF to flow direct to the in radiator tank heat exchanger, so it works 'as intended' with helping heat the ATF up. When 'hot' (iirc it was 50C threshold), the valving shuts forcing the ATF through the cooler fin stack, and onto the in radiator tank heat exchanger...and you sort of think of it as a 'thermal conditioner' of sorts...ie; if you did cool your ATF down to 65C, the coolant will add a little heat, otherwise it works as intended... ...the 'hot' ATF coming from the front bango bolt, is instantiated from the TC when in use, so all/any flash heated oil, flows to the fluid-to-air cooler first, and because of the greater heat differential, you can get rid of this heat fast. Just how big (BTU/h) this cooler needs to be to effectively dissipate this TC flash heat, is the charm...too many variables to discuss here, but I just wanted to point out the nitty-gritty of automatic trans fluid coolers ~ they're a different beastie to what most ppl think of when considering an 'oil cooler'... /3.5cents   
×
×
  • Create New...