Jump to content
SAU Community

Recommended Posts

hey pple i have searched and i could not find what i was looking for :P

at moment im running (splitfire coils )0.8mm gap in my r33 heat range 7 and i was thinking of going to 1.1 mm gap....

would these improve my millage and make the car run better ?

or should i stick to what i have now?

i have read of some people running 1.1 gap successfully with upgraded coil packs?

mods are basic filter,zorst,10psi,coller,splitfires

Link to comment
https://www.sau.com.au/forums/topic/252709-splitfires-and-11mm-gap/
Share on other sites

i know lines drink a lot but if it was able to run on 1.1 plug i tough would make the car run better and in gain receive extra mileage and power .

just reading thru some spark plug threads people seemed to run a 1.1 gap and got a much better burn of fuel making the car run better.

that's why i asked about the bigger gap

You can run a 1.1mm gap, quite easily.

Even on 10PSi...

I run a 1.1mm gap, and was at one point pushing 18PSi off a big huffer turbo, into a 3.0L block, without an issue of misfire.

I was also running 12PSi on the RB25 setup with a 1.1mm gap, without an issue in the world.

The stock plug gap is set at 1.1mm, and the FRESH coils from the factory, will run this, even with a few PSi more being thrown at it, so why wouldn't a set of coils that generate from memory a 50% stronger spark?

You can run a 1.1mm gap, quite easily.

Even on 10PSi...

I run a 1.1mm gap, and was at one point pushing 18PSi off a big huffer turbo, into a 3.0L block, without an issue of misfire.

I was also running 12PSi on the RB25 setup with a 1.1mm gap, without an issue in the world.

The stock plug gap is set at 1.1mm, and the FRESH coils from the factory, will run this, even with a few PSi more being thrown at it, so why wouldn't a set of coils that generate from memory a 50% stronger spark?

thanx for that , i was researching if it would be ok to run a 1.1 plug as per specs as i have new coils and only minor bolt on bits.

the reason for post was to see if anyone else has done it, i did not say i will do it,or will not but, why not ask and save on time and changing sparkies over when you can get a answer from pepole that actually have this setup and running it like MBS206

I agree. Iridiums are a waste of money. What gap you will be able to run with out the car missfiring will depend mainly on the condition of the coilpacks. If they are old and overheated and cracked then the car will missfire. If they are in good condition then it show easily be able to run 1.1 gap.

And i thought splitfires werent any stronger than new stock coilpacks... has this 50% stronger spark been proven?

And i thought splitfires werent any stronger than new stock coilpacks... has this 50% stronger spark been proven?

they must be stronger. i havent heard of anyone running new nissan coilpacks in heavily modified cars. splitfires are a common choice for racing applications.

on my splitfire box it has a graph showing a dyno comparison, an RB making 323ps with regular coilpacks, and 330 with splitfires. theres also another graph which i assume is something to do with spark or volts or something (its in japanese) but the splitfires easily outperform the comparative product.

Ah k just because lots of people say that they arent actually any better. They are just more popular because the are less than half the price of new nissan coilpacks from the dealers. Although i know there are many 400kw gtr's running stock coilpacks without any problems.

With the graph, were the nissan coilpacks old or new. Cos obviously new splitfires are going to outperform 20year old nissan ones..

Ah k just because lots of people say that they arent actually any better. They are just more popular because the are less than half the price of new nissan coilpacks from the dealers. Although i know there are many 400kw gtr's running stock coilpacks without any problems.

With the graph, were the nissan coilpacks old or new. Cos obviously new splitfires are going to outperform 20year old nissan ones..

well thats a very good point. everyone rubbished kkr turbos a while back, many people still do, but they seem to go alright for people who actually tried them, inc. myself.

the graph says splitfire vs "normal", engine is an rb26dett. so if theyre new factory coilpacks, 7ps is a pretty big gain.

i didnt even consider the cost, i though splitfires were fkn expensive. but then again, genuine nissan is a total rip off for just about everything.

LOL yeah apparently genuine new nissan ones cost near $1000 so splitfires are half that price which is why they are a good choice even if they arent any better.

But i guess if they are better than new stock ones thats an added bonus

hey must be stronger. i havent heard of anyone running new nissan coilpacks in heavily modified cars. splitfires are a common choice for racing applications.

on my splitfire box it has a graph showing a dyno comparison, an RB making 323ps with regular coilpacks, and 330 with splitfires. theres also another graph which i assume is something to do with spark or volts or something (its in japanese) but the splitfires easily outperform the comparative product.

the hks drag gtr runs stock coil packs, the only reason ppl go spitfires is cause nissan

want something like $1000 for them brand new

they must be stronger. i havent heard of anyone running new nissan coilpacks in heavily modified cars. splitfires are a common choice for racing applications.

on my splitfire box it has a graph showing a dyno comparison, an RB making 323ps with regular coilpacks, and 330 with splitfires. theres also another graph which i assume is something to do with spark or volts or something (its in japanese) but the splitfires easily outperform the comparative product.

Stronger based on what?

They are not stronger at all.

You are comparing 10-15yr old worn Nissan coils, vs a new coil out of the box, which is wrong. Unless you had brand new coils in your car, your results/testing is incorrect.

If you purchased a NEW set of Nissan coils, put them against Splitfires - you wouldnt know the difference other than one lightens your wallet substancially more than the other.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...