Jump to content
SAU Community

Recommended Posts

yeh pretty much as the title says, having a huge coolant leak from the back of the engine but havent been able to pinpoint where from.

had the car up an put copious amounts of fluid through the radiator and it pisses out the back and from what i can see it gushes out above the gearbox, but there is jus sfa room to have a look where its coming from? ;) any one else similar problem?

i've searched not only this but a few other forums but havent been able to get an answer. jus hoping i could get some sort of an idea before i take it in to a mechanic

cheers for any help

Link to comment
https://www.sau.com.au/forums/topic/253295-r33-s2-leaking-coolant/
Share on other sites

water pump leaking? that tends to be sign of "change me"

hoses to the firewall leaking? ( passenger side)

The drain plug on the engine blow which is on the passenger side leaking?

cant think of much else which could be contributing to a radiator leak at the back of the engine..

Edited by br3ndan
heater hoses

but more than likely the turbo water feed from the back of the plenum.

thats what i was thinking but hoping it wasnt..

thanks for all the help guys will try get some time after work and have a look and take some photos

ok had another look after work today but started to piss down so didnt get much time but its not pump, not the hoses to the firewall im pretty sure its either the heater hoses or the water feed but cant quiet see, pretty sure i've got it pin pointed at the bottom right hand side of the block as u look at it head on.

Taso84 what did you end up having to do with yours?

thanks for any help

this is an absolute broad minded person of a job but you have to do it man

when i did it, it was on my mates s12 w/sr20 conversion and there is NO ROOM at the back

we had to remove the plenum to properly access the hoses

here is a tip: if your struggling undo the gearbox mount and jack the gearbox up higher, it will slope the engine downwards and give you a bit more room to work

here is a pic of the hose i had to replace

post-42017-1232452462_thumb.jpg

sh*t from what i've read this will be aprick of a job or a hit to the back pocket. yeh tell me bout the lack of room its crazy!

yeh i figured i'd be taking some stuff off/out, thanks for the help gfunkk.

jus gunna grab a mate or two and a case an see how we go this weekend i reckon.

cheers for the help fellas

bottom right of an RB - only water above that are heater hoses and the steel turbo feed line.

Or a welsh plug in the block...

go to a mechs and see if they can pressurise your coolant system to allow you to check it exactly.. then see if you want to fix yourself or not

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...