Jump to content
SAU Community

Recommended Posts

Hey guys,

I want to get my R32 resprayed, ive done a search through old threads but they're a bit too old for a proper reference.

So, 2 questions;

1. Who has a current number for Louis at xclusive colours?

2. Who can recommend a spray painter to spray the car? Personal experiences would be appreciated :P

Due to forum rules if you've got anything negative to say about any spray painter in SYdney, please PM me :)

Cheers

Link to comment
https://www.sau.com.au/forums/topic/254280-exclusive-colours/
Share on other sites

thats an outside respray in the same colour for $1500

prices depend on the condition of the car and the colour you want to paint it

give the shop a call and im sure you'll be happy with the price

work is top notch as well

Louie is still around, has moved to a new place on cumberland highway at smithfield (next to Pirtek). Good price and quality work.

Drove past that a few weeks back, wasn't sure if it was his or not. From the street it's very prominent - great big sign out the front so you can't miss it.

XCM 9756 6797..

or,

Andy at Complete Smash Repairs Kirrawee.

Either of these guys will look after you.

Another vote for Andy at Complete Smash Repairs, He recently resprayed Just Japs R32 in the R35 platinum colour looked horn.

Steve, there are a few guys to keep well away from in our area mate.

Sticking with white steveo or is time for some candy red with 10inch gold flake goodness!!

My ex neighbour, has a few vintage cars that he only trusts one place to paint, he is more than impressed with the work, and he isn't impressed easily. He's taken a painter to court for an $8k paintjob, that had a run in the wheel well. I'll grab the shops details when i see him next.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
    • I just stack 2 pieces of 200x50 timber on top of each other. Total length about 900mm, with the top one being a little shorter and both having a 45° angle cut on them to make the front edge a bit of a ramp. Put these in front of each front wheel, drive up on them, throw the trolley jack under. Takes 1 minute. Scissor jacks can eat a bowl of dicks. I never use on under my car unless desperate.
×
×
  • Create New...