Jump to content
SAU Community

Recommended Posts

i have a mate aswell who has a u12 like me and he wanted to know if a ka24de is a east west motor and will it fit in a u12?

KA24DE was used in locally sold U13 Bluebird and is definitely east-west (FWD). I had to fix one recently that had blown the distributor (common problem due to oil seal leak stuffing the internal electronics). Nissan wanted extortionate $$ even at trade prices and I ended up getting one in from the US at a fraction of the price along with all the rocker cover gaskets.

Anyway, the locally sold U12 Pintara came with the CA20E engine (read: boat anchor) as well as the KA24E (single cam) engine in higher spec models (Ti hatch). I'd say dropping in a KA24DE would be a relatively simple swap, but I've never done it so can't say for sure.

mate has a pintara TRX with the ka24E. lump of shite motor, and id say the twin cam version would be only slightly better. In japan the released the same car with 4wd and SR20det power....

think about it :down:

im sure u can get a different sump to suit a rwd application.

OP was asking about FWD application for a U12. U13 Bluebird fits the bill.

KA24DE was certainly available in RWD version. For example, late 90's Navara in Australia (actually both RWD and 4WD versions). In the US there was the popular 240SX (S13 and S14), of course, and even though Nissan never offered a turbo version from the factory, there have been many successful aftermarket turbo kits made for the KA24DE (designated KA24DE-T).

nissan usa released 240sx that had the ka24 rwd (180sx here) pintara in aus has the ka24, not that bad for what they are, would rather an sr20det though as jap u13 bluebird is (sss blubird if you see one look for the sss on the side, means sr20det 4wd inside)

  • 7 months later...
KA24DE was used in locally sold U13 Bluebird and is definitely east-west (FWD). I had to fix one recently that had blown the distributor (common problem due to oil seal leak stuffing the internal electronics). Nissan wanted extortionate $$ even at trade prices and I ended up getting one in from the US at a fraction of the price along with all the rocker cover gaskets.

Anyway, the locally sold U12 Pintara came with the CA20E engine (read: boat anchor) as well as the KA24E (single cam) engine in higher spec models (Ti hatch). I'd say dropping in a KA24DE would be a relatively simple swap, but I've never done it so can't say for sure.

Hello, I tried to PM you but I can't till my post count is at least 10. Was just wanting to know where you got the dizzy for the U13 KA24de motor from? I'm chasing one and retail is $575 at repco, and only a little less than that for trade price. Auto elecs want 300-400 to replace the module. What symptoms does the car get when the dizzy stuffs up? On this one, it has the oil leak as you mentioned, and it sometimes starts then shuts off after a minute, then won't start, and sometimes feels as though it's delivering weak spark.

Looking forward to your reply.

Thanks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...