Jump to content
SAU Community

Recommended Posts

not sure if anyone has seen these parts before... but i visited their shop today and was surprised they make these so cheap:

http://www.vivagarage.com.au/nissan/stagea..._aeroparts.html

Make sure you check the Nissan - Stagea links up the top, because there are more parts available. I had a good look at their R34 stagea today. Looks the goods!

Nigel. SA

Link to comment
https://www.sau.com.au/forums/topic/254842-stagea-body-kits-cheap/
Share on other sites

not sure if anyone has seen these parts before... but i visited their shop today and was surprised they make these so cheap:

http://www.vivagarage.com.au/nissan/stagea..._aeroparts.html

Make sure you check the Nissan - Stagea links up the top, because there are more parts available. I had a good look at their R34 stagea today. Looks the goods!

Nigel. SA

2048150955_97c605f1cc.jpg

nice find....the 34 front looks good...wonder how much labour is to fit it.

More to the point, how much do the rest of the parts cost.. they only list the front bar and fenders... not the bonnet, the hinges, the bonnet latch the headlights the headlight brackets and the radiator support

Got abit excited when it seen the R34 conversion kit and then remembered R34 non xenon headlights are around $1000 a pair then around $2000 for xenon head lights.. bonnets are only $100 for a second hand one so the conversion would be relatively cheap apart from the damn headlights :)

Edited by SHIZNT

Picked up my type M front bumper on Thursday. Currently getting it fitted to my Stagea as we speak, holes are not pre-drilled. Friendly service at Viva Garage and they love to talk about the stags. Once its fitted correctly, I pull it off again for a light rub and spray. :ermm: Just in time for the car show next weekend.

Will post pics when done ... and if it ain't too hot. :banana:

Here's a very rough chop..

Trying to decide do I save my money and slowy buy parts to do a R34 front end conversion and just continue taping the cracks in my bumper.. get another Nismo look alike from Monkey Warehouse or get a Vivgarage Type M bar..

IMG_0027-1.jpg

stagea2.jpg

Do the Viva, I like the look of those kits (Masa) I am planning on getting one for my s2 stag. Plus there looks to be quite a bit of meat on the bottom part of the front bumper so i imagine it would hold up reasonably well. Looking at your nismo front bumper it doesn't look like it would take much to damage that.

Got abit excited when it seen the R34 conversion kit and then remembered R34 non xenon headlights are around $1000 a pair then around $2000 for xenon head lights.. bonnets are only $100 for a second hand one so the conversion would be relatively cheap apart from the damn headlights :P

Where do you find s/hand genuine alloy r34 gtr bonnets for $100. :P

R34 GTT bonnets will not suit.

Pretty sure r34 zenons are about $1600 EACH new.

I would also question the fitment quality of copied Masa R34 guards from Viva. If they have not re-shaped them and just taken a mould from the original Masa guards they would fit even worst.

I have a genuine set of Masa guards and they do not fit perfectly and will be scrapping them soon for some re-worked CCubed copies.

hey Jay .... wasnt that the bumper the caryard had on previous ?

Kinda looks the same but the bar the caryard had on it was a Abflug bar.. there rare as hensteeth to find and are over $1000 for a new one from Abflug in Japan then you have nearly $800 for postage ontop of that..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...