Jump to content
SAU Community

Recommended Posts

Yes,

Get an EBC with dual solenoids and gain control.

Have a read over this thread, and it should seal the deal ;)

http://www.skylinesaustralia.com/forums/Dy...fc-t229928.html

+1

An EBC is a definately good investment. Pretty sure one of the best ones on the market are the Apexi AVCR and the HKS EVCV,

i uses a blitz spec R, it holds boost nicely :happy:

+1

An EBC is a definately good investment. Pretty sure one of the best ones on the market are the Apexi AVCR and the HKS EVCV,

i uses a blitz spec R, it holds boost nicely :happy:

We also discovered this and documented it on here a few years ago...we actually made the same power with less boost switching from AVC-R to Blitz ID-III.

A few AVC-R lovers out there were most upset at me having a go at their bright blue toy.

ba-bow

AVC-R is not dual solenoid, not sure about the HKS EVC

the hks evc uses a stepping motor.

I've used the apexi avcr and now I'm currently running the evc.

My tuner, Matt- Hitman, said i wasted my money. He thinks if tuned properly the avcr is the best out there. So now I'm just using that as my boost gauge.

The blitz dual sbc is the best bang for buck ebc out there. I have a eboost 2 which cost a fortune, if i could do it again i would have got the blitz.

There so basic to set up too

The hks EVCV is the best ebc available but for the price its not warranted.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Fuark, at least the motor survived. What brand was the fitting that snapped?
    • Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...