Jump to content
SAU Community

Recommended Posts

Well as you know i have run a bearing in the GTR.....

I reali have a few choices.....

Im trying to save for a house and really at the moment thats the most important thing....

So i can rebuild the enigine.... $10,000....

I could try and sell the car as is.... What would it be worth? Leaving the wheels, power Fc etc etc etc?

I could strip the car get it back to standered and sell it? Whats it worth then?? And then sell the parts serperate?

Or lastly i could get a rb26 engine for 3000 and put it in my self and sell it... Whats it worth then??

These are just ideas at the mo.. Just tossing up what to do....

Then id get a cheaper car around $10,000 as a daily

Help

Link to comment
https://www.sau.com.au/forums/topic/256567-need-some-advice-what-do-you-think/
Share on other sites

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

Strip parts, new RB26 put the work in and put your parts into new rb26 and sell the old one for cheap, or keep it incase you need to use other stuff off of it. But a cheap daily for like $2k while all this is happening if you don't already have one

I have a whole list of parts thats only done around 1000kms if that...

SARD injectors

Power FC and Controller

Jun Cam Gears

Greedy Profec 2 Boost Controller

Brand New in Plastic Nismo Fuel Pump

Work Xd9s 18 x 10 Brand New Tyres

HKS boost Gauge

Pod Filters (or Standered Air Box)

Thats just the stuff i could replace for standered

Edited by Adz2332
I have a whole list of parts thats only done around 1000kms if that...

depending on size, bout $1000 SARD injectors

$1300 Power FC and Controller

$250? Jun Cam Gears

$350 Greedy Profec 2 Boost Controller

$250? Brand New in Plastic Nismo Fuel Pump

$3000 at least Work Xd9s 18 x 10 Brand New Tyres

$150-200? HKS boost Gauge

$100-150? Pod Filters (or Standered Air Box)

thats approx 6k - 6.5k worth of parts!

Thats just the stuff i could replace for standered

there 700cc injectors

But yer it is roughly that sort of cash in parts...

so if i was selling the car for 24,000 get 6000 for parts get back 30000.....

have to out lay right now around $4000 to get an engine but it in and replace back to standered parts tune etc...

and have a few other little things,

Second blank GTR key,

Brand new Greedy Strut Brace

Brand new Greedy Radiator air guide

Carbon N1 wing

GTR Carbon end caps

Full Exhaust system

Edited by Adz2332

yeh id just slap another rb26 in there, the car is worth bugger all sold with a dead donk. like has been suggested, replace with stock rb26, sell off all good parts from your dead motor and that will more than cover costs

well i am looking for a greddy front strut brace

and i would rather help a fellow sauer out...you know what i mean

wont be much but will be something

so first dibs on the strut brace

well i am looking for a greddy front strut brace

and i would rather help a fellow sauer out...you know what i mean

wont be much but will be something

so first dibs on the strut brace

seagull03.jpg

:huh:

if you ever think about owning a GTR again you will potntialy still have the same problem, and no matter what engine you buy it'll still have the same design flaws unless you fix it... so i say fix this one up if you still want to drive an import, otherwise, sell it and buy some non-turbo local car =P

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Just wanted to pop in an update on my setup. The CD swap has been great, I love the mazworks housing for the overall simplicity. I ended up sealing my trans tunnel with a thin sheet of aluminum reused some of the holes on the trans tunnel, and laid some window sealing EPS foam around the edges. Works great, really quieted things down and sealed up the car.  As for the power comment. Right now I am also running about 650whp. with the way the bell housing is attached to the face of the transmission I have zero doubts it would be fine, mainly because the input shaft and main shaft bearings are seated into the bell housing adapter. This means the load is NOT on the bolts to maintain the power, rather into he casing of the bell housing; Yes the bolts are doing some work there, but with both shafts locked in zero worries.  End of the day, the Mazworks solution is the easiest and safest. no need to take your trans to a shop to get milled perfectly, it fits with minimal clearancing, and you can use all your existing clutch and flywheel.  Driving wise the CD has been great compared to the big box, I'll probably swap my final drive at some point. The serial 9 shifter is gooooood, my only qualm is how tight it is, it takes a fair bit to get use to, 5th and 6th are a bit eh/hard to find at times, but maybe I need re-adjusting, and I think my clutch master is very tired and needs a rebuild. 
    • If you are keen, have a look at my build thread. Car is for sale for the right money or straight swap for a F80 M3 LCI.
    • Welcome mate.  No point in over thinking it, buying any one of those cars you mentioned is not a smart or logical choice with the availability of many "better" (re price to performance) cars available to you.  The heart wants what the heart wants, buy whatever it leads you too.
    • Hey everyone! Im so grateful to be apart of this community and ill do my best to be apart of this. Firstly, i'm not disclosing my real name due to in real life circumstances surrounding my privacy and public image (sorry lol) Secondly, The only thing personal I am willing to share is that I'm from Sydney and a descendant of one of Sydneys largest mortgage firms. I got gifted my first ever car, a 2022 Porsche Cayenne and I love it to death. Ive been driving it for about 5 or 6 months now and honestly Im so grateful for my parents for gifting me this vehicle. However recently I've been working my ass off to afford my second car (which I need help deciding soooooo community help me out please?). Once decided, im planning to try modify it myself. Recent I've been thinking about getting a Skyline, particularly a 25GT or GT-V, yes I know overrated as hell, but I'm also considering a Chaser which I recently came to love. However my dream is to one day own a 180SX (So hard to find clean versions and im not really into importing).  Lastly before I send this off, I want to apologize if I sound tacky or pretentious. I try not to and want to genuinely learn from everyone and anyone. (Im no expert in this area) Thanks for reading!
    • I've got three stashed away but it's starting to get silly with the prices 
×
×
  • Create New...