Jump to content
SAU Community

Recommended Posts

I need to claim back some shed space so I will keep updating the list of parts as I except the fact I cant keep everthing

Bare r32 gtr front cut suit crash repair.....$500.00

r32 gtr front end hubs, control arms, ps rack, complette.....$400.00 or will seperate? pm me

gtr sump modified for rwd (was in my rb26 vl) $400.00

hks pods and adaptors suit 32-33 gtr...$150.00

r33 gtr turbos...(poor condition suit rebuild).....$100.00 pair

rb25et ser 2 motor from stagea new water pump but has blown head gasket.....$800.00 or will seperate? pm me

stagea radiator suit r33gtst also..$150.00

r32 gtr radiator......$150.00

r32 gtr engine harness (has been chopped easy repair)....$80.00

r33 gtr standard rods and pistons only 25k old....$300.00

stagea standard awd auto and transfer worked perfect before removal...$300.00

r32 gtr 5speed box and transfer (no shifter)....$800.00

r32 gtr abs unit ....$200.00

r32 gtr brake master and booster......$250.00

r32 gtr clutch master and booster.......$200.00

hks pod suit gtst afm.....$100.00

3"dump pipe from r33 gtst has had repairs and a flex added looks agricultural but works....$75.00

Trust twin 2.5" twin system suit r33 gtr was running (twin td06 tubos) goes into single 4" at the diff flows big hp....$600.00

Trust twin td05-06 high mount stainless manifold suit rb26....$800.00

gtst r200 4.1 lsd centre...$300.00

various misc parts from r33 rb26 engine and r32 front cut left overs ask I may have what you need

I will add pics as I can or pm me your email, will listen to all resonable offers. parts are in brisbane south I will post at buyers cost. call or text 0431787453 Thank you.

More parts

stainless xforce rb26 low mount manifolds, split dumps and front pipes manifolds and dumps are unused...$800.00 or will seperate.

os twin plate and flywheel suit rb26 push type, used suit reco $400.00

Edited by rb30dett
Link to comment
https://www.sau.com.au/forums/topic/257795-shed-clean/
Share on other sites

stagea standard awd auto and transfer worked perfect before removal...$300.00

how many k's it done ? series 1 or 2 ? think my solenoids just packed in on mine.

and how long has it just been sitting there ?

Link to comment
https://www.sau.com.au/forums/topic/257795-shed-clean/#findComment-4435159
Share on other sites

damn ohwell i'll pay the price then haha.

off topic, how much in total for your conversion ?

I went to rb26 + 5 speed etc but I recon I could do a manual conversion for 3k but without the console. I do all my own work so no labour costs.

Link to comment
https://www.sau.com.au/forums/topic/257795-shed-clean/#findComment-4435185
Share on other sites

Ok I will try to add the pics I have been asked for. I found a couple for other parts to include in the growing list.

r33 gtst turbo (seals gone suit rebuild high flow etc).....$200.00

2x 3" stainless rear mufflers 1 with 4" dump (unused)....$200.00 ea

post-15049-1235105585_thumb.jpgpost-15049-1235105565_thumb.jpg[attachmen

t=207754:clutch.JPG]post-15049-1235105477_thumb.jpgpost-15049-1235105508_thumb.jpgpost-15049-1235105528_thumb.jpgpost-15049-1235105547_thumb.jpgpost-15049-1235105457_thumb.jpg

Edited by rb30dett
Link to comment
https://www.sau.com.au/forums/topic/257795-shed-clean/#findComment-4436693
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...