Jump to content
SAU Community

Recommended Posts

Can anyone test a blitz turbo timer. Mine isn't working, may need repairs. Was working OK, seems to operate OK. Lights up, displays, can change minutes/seconds etc, but will not time down.

Also can anybody tell me the wiring sequence, so I can check that it is OK.

Also is it temperature sensored ie only works if turbo is hot, or does it work every time???

Danny.

Link to comment
https://www.sau.com.au/forums/topic/25821-blitz-turbo-timer/
Share on other sites

Hmmm Not sure what model you have but the last one I used had a factory fault that fired half the dash electrics. Lucky the shop was legit and swapped it out and helped pay for damages.

Anyhow check the handbrake cable is connected correctly and that the dash light turns off when release.

Some HKS I've seen also have this feature.

Link to comment
https://www.sau.com.au/forums/topic/25821-blitz-turbo-timer/#findComment-553040
Share on other sites

Chef I've been thinking about yours, I reckon you need to do a circuit test with a multimeter. I'd guess that your handbrake wire is shorting out on the car body, or your handbrake switch is r/s.

Could be the wires to the warning light, but if the lights working then its more likely the other two.

Danny.

Link to comment
https://www.sau.com.au/forums/topic/25821-blitz-turbo-timer/#findComment-557422
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
    • @GTSBoy yeah sorry i know thery are known for colors bud those DBA are too in colors 🙂 Green will be good enough for me  
    • That's my life. Past-Duncan has a lot to answer for
×
×
  • Create New...