Jump to content
SAU Community

Recommended Posts

Hi Guys,

After much searching myself regarding the "factory boost gauge failing" topic I noticed there's no pictures for those of us who aren't as familiar with every little modules on our cars as some others are.

If you have a Factory boost gauge and it either doesn't work at all or only works at certain times. ( I found myself mine only worked during cold times of the day)

I've found a simple check to determine wether you need to replace your boost sender unit or not.

as stated in many posts I've read there is a boost sensor basically in the middle of your engine bay along the firewall edge above your motor. I feel many are checking this and its lines instead of the unit that controls the actual gauge.

now for the life of me i cannot find to quote the particular post I was hoping to by the gentleman who rectified his sons gauge problem from finding a dry solder join.

If you have access and are confident in using a soldering iron you may not need to read much further.

For those who dont and aren't let me explain a way to solve your mystery.

if you open the boost sender unit between your panel and brake master cylinder you will notice 3 larger solder joints. If you unscrew the 3 screw's holding the inner PCB board.

Raise gently the opposite side of the board as the connector joins are quite hard to lift through the plastic housing. you may de solder these 3 large joints and re solder them properly.

If you aren't confident in soldering you may very gently left the board evenly as so the 3 connection pins pull through the board. they may bend in the direction you pulled them.

now align the 3 connection prongs and re seat the board being careful not to get any dirt inside the. once these are back through they should be sticking out the top by 2mm or so. you can give them a slight bend onto the solder to provide enough connection to test with.

restart your car and check the gauge is working. If it is not after resoldering you may require a new unit. if you chose the non solder path you could be in the same boat however make sure the solder joins are still quite nice and the tips are definatly making contact to them.

I apologise for the quite long write up for such a small task and do stress the non solder option is not a fix, instead it is a mend to test your sender unit is functioning or requires replacement.

the picture quality isnt too great but should be enough to see whilst reading the tut.

post-43187-1235885118_thumb.jpg

shown here inside the red circles are the 3 joints in question.

post-43187-1235885292_thumb.jpg

Hope this helps

-Jayme

Link to comment
https://www.sau.com.au/forums/topic/259107-r34-factory-boost-guage-fault/
Share on other sites

  • 3 weeks later...

you should probs check that it is all plugged in too

that was my problem and because the gage wasn't working when i got my car i never bothered to fix it

i see this topic and i set out to fix the problem i got out all of the tools and then when i had a close look its not plugged in

hahaha lol lol lol lol

2 sec fix lol :down:

  • 2 years later...
  • 1 month later...

Hi guys,

I'm digging up an old thread for a very good reason.

I've had this very issue with the R34 boost gauge dropping out for nearly 3 years, i finally decided i would muck with the boost sender unit and if i broke it i'd need to buy a new one anyway!

So basically as Jamie has stated above, i am very pleased to confirm that if you open up the boost sender unit and simply re-heat the 3 large solder joints shown in the picture in the first post, heat them so they become soft and liquid-ish and then allow them to re-set again (takes 2 seconds), do this to all 3 of the large solder joints and the simply re-assemble the boost sender unit, and go for a drive, your gauge will infact work (read: 'should')

After going out for a 10 min drive, i am super pleased to say that the gauge has not missed a beat, i'll be monitoring it very closely over the next week, but i am highly confident that this has solved the issue.

So if you have this issue, grab yourself a $15 soldering iron fron Bunnings and simply follow the above steps and enjoy the result that is a working boost gauge in your R34!

  • 3 weeks later...

The sensor itself - from my experience - is actually reasonably accurate. The gauge itself is where the problem is - it really doesn't have the granularity in it's markings to be much use beyond 'low boost', 'normal boost' and 'wtf-someething-broke boost'.

After fitting an R34 GTR MFD, this uses the exact same boost sensor, and you actually get much more usable (and useful) boost readings. This is a just MAP sensor after-all, so it should be reasonably accurate.

  • 4 months later...
  • 3 months later...

Hey i just followed your guide and my boost gauge works now thanks heaps :) i used a small flat head screw driver to pop off the 3 clips and i found removing the screw that hold the booster sender unit makes it easier to manuever the unit when u wana pop the clips off and take out the pcb board. thanks alot once again. hope this helps others.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...