Jump to content
SAU Community

Recommended Posts

Im hoping someone can shed some light on the emo cooling system in my r33.

I'll give a quick rundown, prior to water pump install, it would operate at half on guage in traffic and reduce down to anywhere to around a 1/4 dependent on airflow/outside temp etc etc.

But now after the water pump install, its behaving differently, which may not be cause to be concerned but its different...and I dont like it being different.

It now sits at half all the time, and if in traffic tends to drop a little on the gauge(just under half) I am not using any coolant, and cant see any visible leaks. But after the last water pump smashing to the shit, in my paranoia all I can smell is coolant at the front of the car. But despite cleaning it, after the failure, im putting this down to residue.

I have removed the rad cap and its not showing any signs of head gasket issues, bubbles or the like. However after the failure my clutch fan did develop quite a few large cracks between the fins, but surely this wouldn't affect the temps being reduced when airflow is greater? or would it? I have an aftermarket no name radiator.

It happened not immediately after the water pump install, I went for a drive and it was sweet then all of a sudden (probably about 80kays later) the water temp increased and has slowing continued until now its always at the half mark, even coasting down a big hill in 18 degrees do not alter the dash gauge.

Any ideas as to where I might start?

With much thanks,

Danielle

Link to comment
https://www.sau.com.au/forums/topic/259467-cooling-system-issues/
Share on other sites

did you do the pump replacement, or have a shop do it?

sounds from your description that the car didnt have a thermostat before and now it does, the car should sit just under half at all times, regardless of outside temp.

for real?

My friend also has a 33 and his will drop down in temp subject to airflow to around a 1/4 as well. A shop installed the pump, and needed a couple of go's to get it right, there is no way they changed the thermostat, that area has not been touched on that engine ever id say.

Does any one know what the actual heat range is of that gauge?

where does everyone elses rb25 sit on the gauge?

I've got a RB25DET in my 32, and the temp gauge has always sat around the halfway mark (even 40+ with A/c on full blast).

You (and your friend) might have a sticky thermostat that doesn't open / close smoothly. I don't think it will hurt the replace it, anyway.

Not sure if you touched the radiator cap but its possible its starting to fail or is the wrong one. Heres a lesson, an increase in cooling system pressure raises the boiling point of the coolant, this prevents the flashpoint conversion to steam when near cylinder hotspots thus better cooling (higher altitude also reduces atm pressure and lowers boiling point). That smell could be the cap opening prematurely and flushing coolant out of the overflow. Put a new stock cap in or one rated a little higher (not as cold as japan here so dont need the heat). Dont go too high because if the pressure release is rated to high it can burst hoses etc.

The clutch on the fan is could be gone also

My 2 bob

Hi Danielle, My r33 temp gauge sits just under (bee's dick) halfway at operating temp. The thermostate regulates the temp of the coolent in the system. I would remove the thermostate and test it, to be on the safe side. it sound like the thermostate has been sticking open at times before the water pump was done. My fan has a couple of cracks in it as well, thats just from age. If they are really bad replace the fan. I have worked on many nissan vehciles over the years and i've found the temp gauges on various models to site about halfway or slightly under at operating temp.

Regards

Clynton

Thanks for the replies.

Seems like its nothing out of the norm, so nothing to be concerned about...I guess im a little paranoid after smashing a water pump.

Yeah looks like fan is on the to be replaced list. Ah at least thats easy to do!

Cheers again guys.

mine sits at bit unde rhalf way no matter how hot or cold.

As this is the optimum engine temp.

So iwould say b4 it wasnt acting normally due to failing pump and now its fixed and working normally

How did u smash your old one? or do u mean it just failed due to age?

by the sounds of it ur thermostat is faulty, she should stick around the half mark but seeing that were on cooling system issues does anyone know what temp the right "opperating temp" should be? i just did a thermo fan conversion and im not sure if 85c (when the fans kick in) is the optimal temp.coz ever since then she seems to be using more fuel...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
    • There is a warning that "this thread is super old" but they ignore that anyway...
    • With 10% Ethanol, we're talking 2-3% fuel consumption difference. The emissions reductions and octane boost in my opinion far outweigh this almost non existent loss.    My tanks sitting at 80%. Luckily that should go down fast as I'm on vacation again for the next two weeks. 
×
×
  • Create New...