Jump to content
SAU Community

Recommended Posts

You've done a compression test and found a little drop in cylinder no1, so if it was me, thats where i would be looking.

Do a leak down test, theres a good chance no1 will fail the test which more than likely means headgasket.

All the other ideas are good, but when you've got a questionable compression test i would be looking there first.

but did they pressure test it hot? I know of a few now that did not show up under initial testing. car was puit back together and it happend again. crack was only opening up at temp. new head and the problem went away. it can sometimes be hard to diagnose. pourus block is less likely in my experience.

but did they pressure test it hot? I know of a few now that did not show up under initial testing. car was puit back together and it happend again. crack was only opening up at temp. new head and the problem went away. it can sometimes be hard to diagnose. pourus block is less likely in my experience.

I was told it was x-ray'd for cracks.

An x-ray will show up a crack even if it's not hot right?

yeah you would hope so. but my advice would be get it leak tested HOT. people have been fooled before with 26 heads. the cracks is not always easy to find.

Yes, i've checked the water/oil mixture tap, flux capacitor and fusion reactor and they're all fine.

Any other ideas?

No sorry. You have checked everything.. you should pobly pull the engine out and get it fully checked.

  • 2 weeks later...

could it be the block is cracked between where the head bolt goes into it and the water gallery on the outside of the bore.

99% of the time it's the cylinder 5 or 4 one EX side). The crack is usually very small, but grows. If you pull the head off you may not even see it as it starts sub-surface. Skim the block and you'll see it clear as days.

You get trace oil accumulating in your radiator, especially in your overflow? You empty it, it comes back?

The crack is small, but as the oil pressure is greater than the water pressure, it forces the oil through the crack into your water system. Over time, the crack will get bigger, and more will start on other head bolt / gallery places. The harder you drive, the faster it does it.

That is exactly what mine has done in the past

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...