Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Morning *tips hat*

So tis decided. 550cc injectors it is lol :cheers: Anyone know what the go is fitting bigger brake rotors with the stock calipers? I just want to upsize to the Vspec size rotors but keep the calipers. New brackets or what?

Not too sure yet, should know tomorrow sometime, goes on dyno this arvo. Just gotta sit tight and wait, something I hate doing but sadly must be done. Will let ya know when I know more, should be collecting on Thursday around midday.

Morning *tips hat*

So tis decided. 550cc injectors it is lol :cheers: Anyone know what the go is fitting bigger brake rotors with the stock calipers? I just want to upsize to the Vspec size rotors but keep the calipers. New brackets or what?

UAS do an offset bracket to fit the stock calipers with a 324mm rotor (from memory). The work fantastically for a cheap upgrade.

Not too sure yet, should know tomorrow sometime, goes on dyno this arvo. Just gotta sit tight and wait, something I hate doing but sadly must be done. Will let ya know when I know more, should be collecting on Thursday around midday.

Good stuff. You'll have to let me know how it goes!

also...

wish_fan0708-img600x449-13226576735zf84v53715.jpg

You using stock parts or have you found Nismo speedo/tach to go with the dash?

If I can find a Nismo dash, I'll use it. But I'm not paying 11-ty hundred for one....

Here ya go Bozman. But it's damn pricey. $1000 before it even leaves Japland... That and I think they look like they belong in the Delorean.

hotstage2003-img600x450-1322560663c2l3co72281.jpg

Any of you fokkas know if a 33 gtr dash fits a gtst.

I have a whiteface nismo 320 kph dash but i dont wanna pull the chair apart for nothing.

UAS do an offset bracket to fit the stock calipers with a 324mm rotor (from memory). The work fantastically for a cheap upgrade.

This guy knows

$850 with the rotors or $370 odd for just the mounting brackets.

How did you find that lol? Just randomly browsing eastern block drift websites?

There is no fooling you. You're all over it like cheese on a pizza...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...