Jump to content
SAU Community

Rb26 + Vct

sh@un

By sh@un,
in Engines & Forced Induction

 Share

Recommended Posts

Swiper the Fox Grand Master

Swiper the Fox

Posted
Posted
Thinking about adding variable cam timing to my next GT-R. I know HKS had the V-cam setup, but does anyone know if VCT from an RB25 Neo can be adapted to the RB26 head?

Anyone done it? What's involved?

yes it has been done...ive seen it and been in a car with it...amazing results.

Link to comment
https://www.sau.com.au/forums/topic/261777-rb26-vct/#findComment-4486043
Share on other sites
TriniGT Experienced

TriniGT

Posted
Posted

Okay so what about using an RB25 Neo head, on an RB26 block and adapting the individual throttles on the Neo head and a big single or even adapting the twin manifolds to the Neo head? I actually have everything to try this, really has me thinking now. I have a damaged RB26 engine and an extra RB25 Neo head. Just a couple of questions but I will still check it out, will I have to bore the bolt holes in the head to allow for the 26 headstuds? Anything else will I have to mod or it should be fine?

Link to comment
https://www.sau.com.au/forums/topic/261777-rb26-vct/#findComment-4486498
Share on other sites
The Dan Grand Master

The Dan

Posted
Posted

The only difference is the manifold bolt up pattern but guys like ShaneF can make the adaptor plate for you and has done so with the 26 plenum on 25 head.

You will also have to externally feed oil into the vct like the RB30 guys do. But yeah, that would be the most practical way to do it. Both 25NEO and 26 heads have the same flow potential but the camshafts specs are different.

Link to comment
https://www.sau.com.au/forums/topic/261777-rb26-vct/#findComment-4486522
Share on other sites
TriniGT Experienced

TriniGT

Posted
Posted

I am almost done with the indivdual throttle setup on the Neo head, did like GTS4WD and changed the bolt holes and retapped, just need to alter the water neck on the throttle setup to accommodate the VCT solenoid. We'll see how it goes. Yeah may be a little wild but what the heck.

Link to comment
https://www.sau.com.au/forums/topic/261777-rb26-vct/#findComment-4486548
Share on other sites
R34GTFOUR Mentor

R34GTFOUR

Posted
Posted

before you go too far, the combustion chamber in the neo head is smaller than the rb26 head, so that would bump up your CR. I would get the neo head cc'ed first to see how much it will jump up, otherwise sell the neo head and get the normal r33 rb25 head and use that since it has the same cc's as the 26

Link to comment
https://www.sau.com.au/forums/topic/261777-rb26-vct/#findComment-4487476
Share on other sites
Adriano Grand Master

Adriano

Posted
Posted

I believe it could be done quite cheaply, using external solenoids and 2 rb25 intake camgears using either head, however it isnt VCT by any stretch of the imaginiation, and tuning two switch on/off points could be time consuming. You may then have to go away and modify the vct mechanism for different angle throw. IMO if you are going to go to all this effort it would be worth investigating a different mechanism say off an evo or mx5, and get true vct, as dirt said the results would be very worthwhile

Link to comment
https://www.sau.com.au/forums/topic/261777-rb26-vct/#findComment-4487511
Share on other sites
TriniGT Experienced

TriniGT

Posted
Posted
before you go too far, the combustion chamber in the neo head is smaller than the rb26 head, so that would bump up your CR. I would get the neo head cc'ed first to see how much it will jump up, otherwise sell the neo head and get the normal r33 rb25 head and use that since it has the same cc's as the 26

Maybe I can run a thicker headgasket to compensate for the higher CR? Ideally would be to get it CC'ed.

Link to comment
https://www.sau.com.au/forums/topic/261777-rb26-vct/#findComment-4487918
Share on other sites
RB26SX Rookie

RB26SX

Posted
Posted
Okay so what about using an RB25 Neo head, on an RB26 block and adapting the individual throttles on the Neo head and a big single or even adapting the twin manifolds to the Neo head? I actually have everything to try this, really has me thinking now. I have a damaged RB26 engine and an extra RB25 Neo head. Just a couple of questions but I will still check it out, will I have to bore the bolt holes in the head to allow for the 26 headstuds? Anything else will I have to mod or it should be fine?

You would need to run a external oil feed to the head for vct, as the RB26 / RB30 block do not have the oil feed in the block to supply the vct.

Link to comment
https://www.sau.com.au/forums/topic/261777-rb26-vct/#findComment-4490043
Share on other sites
Count Grantleyish Grand Master

Count Grantleyish

Posted
Posted

I found this a workshop in Japan that does NVCS Conversion in RB26 while trawling around on gtr.co.uk forums.

http://www.rising-web.jp/03works/03works_frame.html

Look like it was taken off RB25 to me. And from what I've read above comments, it's more than what it is.

What does it need to have one implanted to a 26, looks to be interesting way to gain power and torque.

Would your average Power FC be able to 'control' the NVCS seeing RB26 doesn't have one?

Is it possible to copy the data on NVCS from RB25 and program it into 26 PFC?

Or better get other ecu that already has the software to support variable timing?

Is it worth going all the trouble for?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/261777-rb26-vct/#findComment-4491992
Share on other sites
GTRNUR Grand Master

GTRNUR

Posted
Posted

I came across this conversion too a while back and it showed some of the machining, head modifications to the oil galleries to hook up an external oil feed etc. They used an inline solenoid to supply oil from the oil pressure sender line to valve, and then used a RB25DET intake cam and gear.

I cant find the pics, but they used a -4 oil fitting screwed into the front of the head and then had drilled galleries to supply the cam gear.

Link to comment
https://www.sau.com.au/forums/topic/261777-rb26-vct/#findComment-4492545
Share on other sites
rob82 Mentor

rob82

Posted
Posted

Delphi make a cam phasor for belt driven camshafts - as used on the EVO9. You could probably adapt the solenoid from the EVo9 as well. Remember that full cam control is a bitch for most speed density sytems and that total "bump and check" cam phasing is alot of work for not much gain. Your better off with just an on and off cam advance solenoid

Link to comment
https://www.sau.com.au/forums/topic/261777-rb26-vct/#findComment-4494691
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      Waaay ahead of ya....(evil laugh!!) Will show the fitment and spec details later when it isnt as rainy !
    • wizlb
      Flex Fuel Kit Workshop

      By wizlb · Posted

      Thanks Dose.....    I appreciate it!!
    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • Piggaz
      Ogura orc1000f vs Osg tr2cd vs Osg r3c experiences, max torque/max hp?

      By Piggaz · Posted

      I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • uchoa
      Yet another RB Neo misfiring thread after reading all the others.

      By uchoa · Posted

      Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
×
×
  • Create New...