Jump to content
SAU Community

Wreaking Rolled R33 S2

Driftin~Davo
 Share

Recommended Posts

Driftin~Davo Enthusiast

Driftin~Davo

Posted
Posted

Hey I gotta rolled R33 with all the good stuff gone lol. If anyone needs annoying interiour crap pwr window motors switches etc PM me.

Location: Caboolture.

I will get a better list up soon and sum pics but this is what is available so far:

-Standard shocks with ultra low king springs - $120

-Manual conversion stuff (tailshaft, clutch master lines slave, clutch & break peddle box - $150

-ABS stuff $$$ offers?

-Air bag stuff $$$ offers?

-The boot is the only undammaged panel and has a GTR lookn wing - $150

-AC system is still intact $$$ offers?

-Drivers side S2 headlight - $350

Link to comment
https://www.sau.com.au/forums/topic/262977-wreaking-rolled-r33-s2/
Share on other sites
Driftin~Davo Enthusiast

Driftin~Davo

Posted
  • Author
Posted
Hi mate, I'm after a front left hub if you still have them and they are alright

Cheers

Tim

Nar soz front crossmember, rear cradle, breaks n hubs all gone.

Driftin~Davo Enthusiast

Driftin~Davo

Posted
  • Author
Posted
hey mate got an engine xmember and/or radiator ? if so ... where u at and how much ..delivered to 4207?

Soz dude Rad died in roll and xmember is gone.

Driftin~Davo Enthusiast

Driftin~Davo

Posted
  • Author
Posted
Hey chief, how much you want for the set of front and rear brakes,

oh and maybe the brake master cylinder.

Breaks are gone soz. Break master - $50

Driftin~Davo Enthusiast

Driftin~Davo

Posted
  • Author
Posted (edited)
Series 1 or 2?

Have u got Rear SKYLINE garnish? If Series 2 what colour?

Cheers

Its a series 2, white in colour. by the rear garnish do u mean where is says skyline on the boot?

Oh and can anyone give me a heads up on how to edit and update my first post? there's no edit tab wtf lol soz for the newbie q's havnt used SAU for a while. cheers.

Edited by Driftin~Davo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...