Jump to content
SAU Community

Dyi:how To Replace Speedo Cable? Need Help

cobrAA
 Share

Recommended Posts

cobrAA Mentor

cobrAA

Posted
Posted

So well I broke the little cheap plastic thing when I was changing my light for LED on my cluster. So I ordered my cable from nissan. I searched a lot. and I learn that the cable is connected to the gearbox and pass throught the firewall.

But euh.. does some have picture of where exactly it goes? and how do you disconnect it? Will I have to change the fluid after?

Thanks :D

predator Grand Master

predator

Posted
Posted

I assume this in an R32 ?

There are three bolts to undo in the engine bay, near the steering column. Undo these, pull cable to the left in the cabin, and it will come out from its slot. Pull from the engine bay, making sure now and then it's not getting caught on something. Crawl under car, unclip cable from brackets, unscrew shield from gearbox..

Fit new cable reverse of this.

No you will not have to change your gearbox oil.

cobrAA Mentor

cobrAA

Posted
  • Author
Posted (edited)
I assume this in an R32 ?

There are three bolts to undo in the engine bay, near the steering column. Undo these, pull cable to the left in the cabin, and it will come out from its slot. Pull from the engine bay, making sure now and then it's not getting caught on something. Crawl under car, unclip cable from brackets, unscrew shield from gearbox..

Fit new cable reverse of this.

No you will not have to change your gearbox oil.

So I tried to change it today. WASTED 3 HOURS OF MY TIMESicon_ChairShot.gif.

How the heck do you UNBOLT THOSE 3 BOLTS?? Is there a special tools? I can't do it with a tiny screwdriver because I don't have enought force. With a long screwdriver it just wont fit.

And with a ratchet, I don't have enought space to ''wind up''

PLEASE HELP!001_help.gif001_help.gif001_help.gif001_help.gif001_help.gif

My car is a BNR32

Edited by cobrAA
predator Grand Master

predator

Posted
Posted

You will need a socket, or spanner (I think it's a 10mm) and nimble hands :) but no special tools required. There isn't much room I agree to move around, maybe less so on a GTR.

If you jack up the car, it may be easier to do it from underneath.

Russman Grand Master

Russman

Posted
Posted

Yeah 10mm bolts. 3 of em. ratched with extensions is all you need. The whole plate comes off the firewall. I did have my dash out as I think there is a clip just before it goes into the back of the cluster.

It's a simple job.

cobrAA Mentor

cobrAA

Posted
  • Author
Posted

Okay . 4 hours later. Job is still not done. So I'm down to a 6 hours spent and still not done...

How do you insert the gearbox cable end STRAIGHT??? I spent the last hour trying to bolt it but it will always go too much to the right, too low, too high. It just wont ****in go straight and fit so I can bolt it.

I did insert the metal piece in the hole of the gear box but I just can't bolt the bolt on the gearbox because it is misaligned..

Please Help serioulsy. I'm really about to sell my gtr because of that freakin stupid 70$ mods.

cobrAA Mentor

cobrAA

Posted
  • Author
Posted (edited)
umm i thought the cable that fits into the gearbox end has a notch and fits only 1 way.. bugger.. maybe try with the old cable on the gearbox to see how it fitted

For sure it is one way, but since the cable is so ''strech'' it wont hold in place. so it will make my bolt ''offset'' so i can't screw it forward.And the force is so big that I can't hold the cable at the ''right'' place with one hand and screw with the other.

Hope you understand what I mean?

Edited by cobrAA
R.3.2.G.T.R Grand Master

R.3.2.G.T.R

Posted
Posted

have u already plugged in the other end to the cluster?? from memory, my cable had a nice loop before coming into the gearbox, certainly wasnt strained like yours??

dont know if gts-t cables are any shorter, maybe wrong cable supplied by nissan.. gts-t ones have few teeths to the gtr so wont work on gtr but not sure if length is different

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...