Jump to content
SAU Community

Dyi:how To Replace Speedo Cable? Need Help

cobrAA
 Share

Recommended Posts

cobrAA Mentor

cobrAA

Posted
Posted

So well I broke the little cheap plastic thing when I was changing my light for LED on my cluster. So I ordered my cable from nissan. I searched a lot. and I learn that the cable is connected to the gearbox and pass throught the firewall.

But euh.. does some have picture of where exactly it goes? and how do you disconnect it? Will I have to change the fluid after?

Thanks :D

predator Grand Master

predator

Posted
Posted

I assume this in an R32 ?

There are three bolts to undo in the engine bay, near the steering column. Undo these, pull cable to the left in the cabin, and it will come out from its slot. Pull from the engine bay, making sure now and then it's not getting caught on something. Crawl under car, unclip cable from brackets, unscrew shield from gearbox..

Fit new cable reverse of this.

No you will not have to change your gearbox oil.

cobrAA Mentor

cobrAA

Posted
  • Author
Posted (edited)
I assume this in an R32 ?

There are three bolts to undo in the engine bay, near the steering column. Undo these, pull cable to the left in the cabin, and it will come out from its slot. Pull from the engine bay, making sure now and then it's not getting caught on something. Crawl under car, unclip cable from brackets, unscrew shield from gearbox..

Fit new cable reverse of this.

No you will not have to change your gearbox oil.

So I tried to change it today. WASTED 3 HOURS OF MY TIMESicon_ChairShot.gif.

How the heck do you UNBOLT THOSE 3 BOLTS?? Is there a special tools? I can't do it with a tiny screwdriver because I don't have enought force. With a long screwdriver it just wont fit.

And with a ratchet, I don't have enought space to ''wind up''

PLEASE HELP!001_help.gif001_help.gif001_help.gif001_help.gif001_help.gif

My car is a BNR32

Edited by cobrAA
predator Grand Master

predator

Posted
Posted

You will need a socket, or spanner (I think it's a 10mm) and nimble hands :) but no special tools required. There isn't much room I agree to move around, maybe less so on a GTR.

If you jack up the car, it may be easier to do it from underneath.

Russman Grand Master

Russman

Posted
Posted

Yeah 10mm bolts. 3 of em. ratched with extensions is all you need. The whole plate comes off the firewall. I did have my dash out as I think there is a clip just before it goes into the back of the cluster.

It's a simple job.

cobrAA Mentor

cobrAA

Posted
  • Author
Posted

Okay . 4 hours later. Job is still not done. So I'm down to a 6 hours spent and still not done...

How do you insert the gearbox cable end STRAIGHT??? I spent the last hour trying to bolt it but it will always go too much to the right, too low, too high. It just wont ****in go straight and fit so I can bolt it.

I did insert the metal piece in the hole of the gear box but I just can't bolt the bolt on the gearbox because it is misaligned..

Please Help serioulsy. I'm really about to sell my gtr because of that freakin stupid 70$ mods.

cobrAA Mentor

cobrAA

Posted
  • Author
Posted (edited)
umm i thought the cable that fits into the gearbox end has a notch and fits only 1 way.. bugger.. maybe try with the old cable on the gearbox to see how it fitted

For sure it is one way, but since the cable is so ''strech'' it wont hold in place. so it will make my bolt ''offset'' so i can't screw it forward.And the force is so big that I can't hold the cable at the ''right'' place with one hand and screw with the other.

Hope you understand what I mean?

Edited by cobrAA
R.3.2.G.T.R Grand Master

R.3.2.G.T.R

Posted
Posted

have u already plugged in the other end to the cluster?? from memory, my cable had a nice loop before coming into the gearbox, certainly wasnt strained like yours??

dont know if gts-t cables are any shorter, maybe wrong cable supplied by nissan.. gts-t ones have few teeths to the gtr so wont work on gtr but not sure if length is different

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...