Jump to content
SAU Community

Recommended Posts

Hey guys,

Pulled apart a Wrecked White R32 GTR last weekend. Would like to sell of as much as i can. Currently have the front half as a half cut, and the rest is in parts. Am negotiable on most, so please ask.

Items listed below:

Front cut includes 76000 km Motor/Box/Loom/ECU/brake master/Clutch master and slave/new twin plate clutch/ dumps/dash/turbos and just about everything you'll find in an engine bay, except cooler and piping. - $6000 or near offer.

Fuel pump $140

Fuel Door $40

Fuel tank $40

Drivers Door (Trim+Cont) $50

Passenger Door (complete) $150

Rear Rio Bar $50

Rear bumper $200

Rear Tail lights Pair $120

Rear boot lid (wing + badges) $250

Rear reverse lights Pair $30

GTR Steering Wheels x2 $100ea

Left Front Indicator $90

Fog Lights (Pair) $75

Factory Cold air box $80

GTR Grill $130

Front Rio Bar $50

Front Bumper (2x cracks) $200

Twin Factory Dumps $5

Blitz FMIC $250

HKS Piping (RB26DETT) $150

Side Skirts $150

Set of Side Pods $150

Right F guard (damaged) $250

Left F guard (perfect) $400

Pair Headlights $350

Left Front Guard Liner (perfect) $80

Rear GTR coilovers $150

Front Trust Coilovers $200

Aluminium Bonnet $300

Rear seats SOLD


Glove box $10

Factory Gear Knob $2

Momo gear knob $5

Rear cradle $400

Tailshaft $200

Rear callipers, rotors $400

Front callipers, rotors $500

Rear sway bar $200

Front sway bar $100

Front LCA (pair) $200

Front Upper Arms $100

Seat belts x4 $80

R32 GTR Diff $900

Radiator $175.

PICTURES : http://img291.imageshack.us/gal.php?g=dsc01036.jpg

Either PM me or call on 0431657139.

I would like to move this stuff on.

Im located in The Gap, Brisbane. Would prefer pick-ups, but talk to me.

Thanks Guys

Jason

Link to comment
https://www.sau.com.au/forums/topic/263484-r32-gtr-stripped/
Share on other sites

Hey mate, intrested in:

Steering wheel

FMIC

Factory Gear nob

Seat Belts (if original items)

I live in Mitchelton, brisbane, which is just around the corner. Send me a PM with your phone number ill arange a time to come out and have a look at what you have.

Regards

Ian

  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...