Jump to content
SAU Community

Changing From Side Feed To Top Feed For Fuel Injectors

MissR34

By MissR34,
in South Australia

 Share

Recommended Posts

MissR34 Grand Master

MissR34

Posted
Posted

Hey all

normally i wouldnt post something like this, but i know some of you may know what the deal is with changing from side feed injectors to top feed? has anyone in sa actually done it?

nos man Mentor

nos man

Posted
Posted (edited)

whatsisname is the man to ask! but i thought neo 6 were top fed anyway?

but it is more costly changing to top fed because you need to get a fuel rail made! but i went for it because i thought maybe later on i might need to go for bigger injectors and there is a bigger variety of top fed then side fed

Edited by nos man
MissR34 Grand Master

MissR34

Posted
  • Author
Posted

i need 1000cc injectors and i cant find any for the RB25

the other option i was thinking was maybe going with RB26 fuel injectors and getting a RB26 Fuel Rail to match but i dunno if that will work either!

nos man Mentor

nos man

Posted
Posted (edited)

1000cc are pretty big injectors! aiming for huge numbers or something?

but rb26 injectors should fit into neo 6 motors! no need for fuel rail i don't think but they're like 440-480cc injectors?

edit. rb25 neo, rb20 and rb26's all run top fed injectors! it's the r33 rb25 that runs side fed

Edited by nos man
Luke_ENR34 Grand Master

Luke_ENR34

Posted
Posted (edited)

I got 870cc Bosch Siemens Injectors forsale. $600

Came out Phu's old 34 im pretty sure.

Edit, 34's are top feed anyways.

Edited by Luke_ENR34
MissR34 Grand Master

MissR34

Posted
  • Author
Posted
1000cc are pretty big injectors! aiming for huge numbers or something?

but rb26 injectors should fit into neo 6 motors! no need for fuel rail i don't think but they're like 440-480cc injectors?

edit. rb25 neo, rb20 and rb26's all run top fed injectors! it's the r33 rb25 that runs side fed

yeah the supercharger im getting is 800 hp with a 1200 CFM on it :thumbsup:

dangerman4 Mentor

dangerman4

Posted
Posted

are you taking the piss Cara or you are seriously thinking of putting a 800 hp super charger on your car?

ive seen you drive NA and i can asure you with anything over 300 hp you will become a statistic.

please be careful.

D_Stirls Veteran

D_Stirls

Posted
Posted

RB25 NEO's run top feed high impedance injectors. i would suggest wiring in a resistor pack from a GTR and running low impedance injectors for a couple reasons. Because the injectors you use will then be the same as the GTR injectors there was more of a market than the high impedance injectors used on the RB20's and therefore should be slighly cheaper. Also low impedance injectors are a lot easier to control when running low duty cycles.

If you are going to be making 800hp then you will need to run an after market rail (probably 14mm injectors as well) and you will have to upgrade your fuel lines from the tank, it'll be expensive but i'm sure you weren't expecting it to be cheap.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • drifter17a
      R34 gtt rb25det neo timing belt kit

      By drifter17a · Posted

      So now doing the change and first time dealing with rb so little nervous giving engine power and potential for screwing it up When you align all marks and then remove crank bolt, timing move little I assume you can put the bolt back in once you have removed the pully to get timing to where you want?   here is pic of my both intake and exchust cam aligned, depending on angle you look they seem to be either aligned or a half tooth or so out. Any thoughts? Should you angle your face and look at each mark that way as if looking straight rather than from above as it can be misleading   <a href="https://ibb.co/ZpnhcvbF"><img src="https://i.ibb.co/HfWrGR9b/IMG-4447.jpg" alt="IMG-4447" border="0"></a> <a href="https://ibb.co/4wm2wn4q"><img src="https://i.ibb.co/JWBqWwr1/IMG-4445.jpg" alt="IMG-4445" border="0"></a>   https://ibb.co/ZpnhcvbF https://ibb.co/4wm2wn4q
    • sunsetR33
      braided lines for the turbos

      By sunsetR33 · Posted

      Thanks for the reply @GTSBoy Haven't really thought of that yet, but you are right. If the hose was damaged it should be absolutely pissing by now. I'll put some heat sleeve around it for good measure since I'm already removing the line anyway.  Maybe I'll put on some of the stock hardlines if I ever fully remove the turbos again. Maybe when T51R modding the compressor housings? Might be a fun mod on GT28s for that "fake single turbo" effect.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 1: I did some work on the car already before finalizing this post and my "issues" list. I dropped the Tomei exhaust in favor of the HKS Hi Power Silent. Sounds nice and I can actually hear myself think now. Also gives me a realistic chance to legally drive without silencer inserts. A bit of cheating was necessary to still be able to mount the Top Secret style diffuser. Some malusage of washers and a bit of "convincing" toward the brackets and exhaust hanger seemed to do the trick. The shaky steering wheel has been resolved as various suspension components were worn, like sway bar bushings and link bars. Most notably the two steering tie rod ends. Had some trouble finding bushings because my sway bars are not OEM thickness, 23.x up front and 27 rear. But non adjustable, so no aftermarket I suppose. Maybe they are nismo units? Turbo oil drain hoses were definitely still the originals and are new now. Wasn't the cause of the turbo oil leak sadly. Currently removing the rear turbo because of it, I suspect the braided oil feed line is the culprit. This issue needs to be dealt with so I can work towards actually getting the turbo setup legal and inspected. Two new issues to add to the list as well. Rear Main seal is probably leaking. Time will show how bad it is, I don't really want to drop the gearbox right now just for the stupid seal. Could fix a few other things in one go once I do that. Front right driveshaft grease is going past the cv boot, so at some point I'll fix that too.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Ok so no 4cyl clutch... Yeah it is a factory manual. So if iam correct i need clutch and flywheel too? I can use something that suits something like R32 GTST?   EDIT: https://www.ebay.com/itm/224291042776 Is this ok?   EDIT2: i maybe forget to mention this(dk how important it is) but the trans will be behind RB25DET NEO(iam doing swap) It will be there for a little while. Iam planing to do bigbox or BMW tranny..
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      You're probably right about that one. Thanks for your suggestions, I hope I don't need a new 3rd brake light. Although wiring issues might arguably be worse. Right now I'm in the midst of a turbo removal because of my oil leak, other problems are going to have to wait for now.
×
×
  • Create New...