Jump to content
SAU Community

R34 Gtt - Getting All 4 Rear Lights Showing When Braking?

nuffsaid
 Share

Recommended Posts

nuffsaid Veteran

nuffsaid

Posted
Posted

Hi all

Does anyone know how to get all 4 rear lights lit up when braking?

I heard it's possible, however the brake light bulbs are easily blown if not done correctly, especially if the parking lights are on.

Is there a guide on how to do this properly?

Thanks

ashneel Grand Master

ashneel

Posted
Posted

getting my dad to do this for me as he loves these kinda things.

from what i know what you will need is 2 double filament globes (same as you normal brake light but a size smaller so it fists the hole) and an inline fuse and globe holder.

locate which wire is the brake line wire splice into it it and run the wires to the right fittings int he new globe holder thing and presto.

its easy to do and kinda fiddley thats why my dads doing it for me lol but ye if no one has done this by next sunday ill have mine done by then and will put up a detailed instruction.

STYLN Collaborator

STYLN

Posted
Posted (edited)

checked mine last night and all four tails brighten up when i brake, plus the small light top of boot lights up.

is that a standard thing on gtt? or is it gtt 4 door or has mine been modified i wonder??? I know i didnt do it... Pic below any help???

21042009126.jpg

Edited by STYLN
ducki Proficient

ducki

Posted
Posted (edited)

I think all 4 door has 4 lighting up cause that's the first thing I notice when I see a 4 door. Haven't seen any 2 door with 4 lighting up so far. Loved to do it to mine.. I thought it was just splicing the smaller light wire and join it to the main brake wire. I mean the ground wire of those 2.

Edited by ducki
  • 5 months later...
UnCo Rising Star

UnCo

Posted
Posted

All four stay lit as in when you hit the brakes?

It'd be interesting to see if there are any noticable changes to the wiring.

Wouldn't happen to have time to take some pics would you? :)

.:: GimpS-R34 ::. Grand Master

.:: GimpS-R34 ::.

Posted
Posted

as in the two smaller ones stay lit.. but don't go bright when i brake like the big ones..

i only noticed this when i replaced with just jap LED ones.. but am unsure if they were always like it.. i'm sure i could take a pic of the wires

UnCo Rising Star

UnCo

Posted
Posted

Oh I think what you're talking about is the normal setup.

Both the outer and inner circles are lit when you have your lights on.. but when you hit the brakes, only the outer ones will go brighter.

I'm hoping to wire it so that even when I don't have the parkers on and I hit the brakes, all four will light up.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Chupapy
      Help! Leak coming under transmission

      By Chupapy · Posted

      Thanks for the reply mate. Well I really hope its a hose then not engine out job
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      But.... the reason I want to run a 60 weight is so at 125C it has the same viscosity as a 40 weight at 100C. That's the whole reason. If the viscosity changes that much to drop oil pressure from 73psi to 36psi then that's another reason I should be running an oil that mimics the 40 weight at 100C. I have datalogs from the dyno with the oil pressure hitting 73psi at full throttle/high RPM. At the dyno the oil temp was around 100-105C. The pump has a 70psi internal relief spring. It will never go/can't go above 70psi. The GM recommendation of 6psi per 1000rpm is well under that... The oil sensor for logging in LS's is at the valley plate at the back of  the block/rear of where the heads are near the firewall. It's also where the knock sensors are which are notable for 'false knock'. I'm hoping I just didn't have enough oil up top causing some chatter instead of rods being sad (big hopium/copium I know) LS's definitely heat up the oil more than RB's do, the stock vettes for example will hit 300F(150C) in a lap or two and happily track for years and years. This is the same oil cooler that I had when I was in RB land, being the Setrab 25 row oil cooler HEL thing. I did think about putting a fan in there to pull air out more, though I don't know if that will actually help in huge load situations with lots of speed. I think when I had the auto cooler. The leak is where the block runs to the oil cooler lines, the OEM/Dash oil pressure sender is connected at that junction and is what broke. I'm actually quite curious to see how much oil in total capacity is actually left in the engine. As it currently stands I'm waiting on that bush to adapt the sender to it. The sump is still full (?) of oil and the lines and accusump have been drained, but the filter and block are off. I suspect there's maybe less than 1/2 the total capacity there should be in there. I have noticed in the past that topping up oil has improved oil pressure, as reported by the dash sensor. This is all extremely sketchy hence wanting to get it sorted out lol.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I neglected to respond to this previously. Get it up to 100 psi, and then you'll be OK.
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      I agree with everything else, except (and I'm rethinking this as it wasn't setup how my brain first though) if the sensor is at the end of a hose which is how it has been recommended to isolate it from vibrations, then if that line had a small hole in, I could foresee potentially (not a fluid dynamic specialist) the ability for it to see a lower pressure at the sensor. But thinking through, said sensor was in the actual block, HOWEVER it was also the sensor itself that broke, so oil pressure may not have been fully reaching the sensor still. So I'm still in my same theory.   However, I 100% would be saying COOL THE OIL DOWN if it's at 125c. That would be an epic concern of mine.   Im now thinking as you did Brad that the knock detection is likely due to the bearings giving a bit more noise as pressure dropped away. Kinkstah, drop your oil, and get a sample of it (as you're draining it) and send it off for analysis.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I myself AM TOTALLY UNPREPARED TO BELIEVE that the load is higher on the track than on the dyno. If it is not happening on the dyno, I cannot see it happening on the track. The difference you are seeing is because it is hot on the track, and I am pretty sure your tuner is not belting the crap out of it on teh dyno when it starts to get hot. The only way that being hot on the track can lead to real ping, that I can think of, is if you are getting more oil (from mist in the inlet tract, or going up past the oil control rings) reducing the effective octane rating of the fuel and causing ping that way. Yeah, nah. Look at this graph which I will helpfully show you zoomed back in. As an engineer, I look at the difference in viscocity at (in your case, 125°C) and say "they're all the same number". Even though those lines are not completely collapsed down onto each other, the oil grades you are talking about (40, 50 and 60) are teh top three lines (150, 220 and 320) and as far as I am concerned, there is not enough difference between them at that temperature to be meaningful. The viscosity of 60 at 125°C is teh same as 40 at 100°C. You should not operate it under high load at high temperature. That is purely because the only way they can achieve their emissions numbers is with thin-arse oil in it, so they have to tell you to put thin oil in it for the street. They know that no-one can drive the car & engine hard enough on the street to reach the operating regime that demands the actual correct oil that the engine needs on the track. And so they tell you to put that oil in for the track. Find a way to get more air into it, or, more likely, out of it. Or add a water spray for when it's hot. Or something.   As to the leak --- a small leak that cannot cause near catastrophic volume loss in a few seconds cannot cause a low pressure condition in the engine. If the leak is large enough to drop oil pressure, then you will only get one or two shots at it before the sump is drained.
×
×
  • Create New...