Jump to content
SAU Community

Recommended Posts

ok, well bombtrack and i are building a ke70 with an SR20det for a drift pig.

money is not huge on this build and we're aiming for around 200rwkw @ 950kgs stripped

planning on using an stock r34 turbo we have lying around and running e85

now a pfc is obviously the best cheapish option

BUT

could we get away with just a SAFC2 & an SITC?

e85 uses around 30% more fuel and is useless with out timing adjustment so an sitc would be needed, but will the safc be able to bend the signal far enough for the fuel? i dont have any real experience with safc's

i figure both could be had for around $500 second hand so its gonna be half the price of a pfc

Link to comment
https://www.sau.com.au/forums/topic/267728-sr20-ecu/
Share on other sites

$420 will get you a nistune chip + Tuner license ($220 for chip alone if some one else is going to tune it). $120 for a consult cable(Not needed if your not the tuner)

This will allow you to remap the stock ECU realtime. This will be just as good as a power FC and alot better than any piggy back system.

Link to comment
https://www.sau.com.au/forums/topic/267728-sr20-ecu/#findComment-4564853
Share on other sites

R34 turbo on SR20 ...

Aren't the flanges different???

You could make 200rwkw on E85 EASILY on a stock SR20 toooobo

Ben - dont get Trent into trouble and make him advertise, just send him a PM.

Although you know what Hamish - SR20 ECU's run pig rich, so running E85 on a stock ECU might lean it up nicely - sure it might ping a bit, but it would be free :P

Link to comment
https://www.sau.com.au/forums/topic/267728-sr20-ecu/#findComment-4568467
Share on other sites

ok, well bombtrack and i are building a ke70 with an SR20det for a drift pig.

money is not huge on this build and we're aiming for around 200rwkw @ 950kgs stripped

planning on using an stock r34 turbo we have lying around and running e85

now a pfc is obviously the best cheapish option

BUT

could we get away with just a SAFC2 & an SITC?

e85 uses around 30% more fuel and is useless with out timing adjustment so an sitc would be needed, but will the safc be able to bend the signal far enough for the fuel? i dont have any real experience with safc's

i figure both could be had for around $500 second hand so its gonna be half the price of a pfc

you can pick up a PFC without hand controller for under $700 if u shop around, and it has a better resale value than any of the other options when ur finished with it.

Link to comment
https://www.sau.com.au/forums/topic/267728-sr20-ecu/#findComment-4568676
Share on other sites

R34 turbo on SR20 ...

Aren't the flanges different???

You could make 200rwkw on E85 EASILY on a stock SR20 toooobo

Although you know what Hamish - SR20 ECU's run pig rich, so running E85 on a stock ECU might lean it up nicely - sure it might ping a bit, but it would be free :blink:

lol... d00d that is even too ghetto for teh pig...

yeah, was thinking of using an adaptor plate for the 34turbo, as we have one lying around (and a 33 one) but after speaking to trent i'm just gonna get a 2nd hand s15 turbo

you can pick up a PFC without hand controller for under $700 if u shop around, and it has a better resale value than any of the other options when ur finished with it.

true dat, but trent has hooked me up with a nistune board in ecu an case, so i'm stoked! deal DONE :)

Link to comment
https://www.sau.com.au/forums/topic/267728-sr20-ecu/#findComment-4568954
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...