Jump to content
SAU Community

Dyno Day - Aussie Vs Imports - Springy Motors - Sat 27th Of June 2009, Need Some Nissan Cars To Represent!


Recommended Posts

5k for 400kw! thats cheating! any 400kw skylines around? i m sure there are

Im going to rebuilding my engine in the next 6 months, any one wanna donate a 600hp shot of nos to finish this engine off :)

http://www.skylinesaustralia.com/forums/Tu...88-t237291.html

Edited by W0rp3D
They will take turns running on the dyno.

A total will be calculated by the end of the day.

The highest all wheel kw will be given the win.

sorry but as i read it, they will add the 10 cars together and the total of all 10 will win? is that correct? or will it still be the highest number of all 20 takes it out?

is c fuel aloud or is it pump only??

sorry but as i read it, they will add the 10 cars together and the total of all 10 will win? is that correct? or will it still be the highest number of all 20 takes it out?

is c fuel aloud or is it pump only??

Yep, take all the Aussie figure and add them up then take all the Jap figure and add them up and they're the final results for each class

You should definitely run your car!

Pretty sure I read somewhere that the car went bang?

^^Ujin you should have a run.

You just hit 320 kW's on your last dyno and see if Springy Motors differ in reading.

we will see how it goes.. i m still waiting on some parts to come in followed by a full tune.. if its al done in time i might enter my car lol.. :)

  • 2 weeks later...
  • 4 weeks later...

when is the aussie vs import day going to be on, have the dates been decided? i have a gtr and a mates vz 6.0l with abit of work done to it and we are keen to chuck them on the rollers

Guest
This topic is now closed to further replies.


  • Latest Posts

    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
×
×
  • Create New...