Jump to content
SAU Community

Recommended Posts

from the little info we have I would say it's a poor tune. simple as that. the car should not run poorly over a change in altitude of 400m.

hmmm, as stated my STI did the exact same thing, different car different tuner?

If it is a temp and barometric pressure issue, it could be far more than 5% if none of it is corrected, however 10% still shouldnt be enough, however i have seen it happen without the use of an air temp sensor, basically in summer blowing black smaoke, and lean in winter.

If it is a temp and barometric pressure issue, it could be far more than 5% if none of it is corrected, however 10% still shouldnt be enough, however i have seen it happen without the use of an air temp sensor, basically in summer blowing black smaoke, and lean in winter.

crap, so how is that fixed?

cheers

how? with a real tune & a real ecu - ie go back to the PFC or get the link installation sorted and tuned properly

if its got a map sensor it should be setup accordingly, along with air temp sensor to correct itself

* WINNER *

how? with a real tune & a real ecu - ie go back to the PFC or get the link installation sorted and tuned properly

if its got a map sensor it should be setup accordingly, along with air temp sensor to correct itself

* WINNER *

yeah but it had a power fc in it before (tuned by another tuner) and it ran sweet till it came to queenstown, then again ran like crap

Im not sure if you can do anything about the barometric pressure compensation, as that should be built into the firmware of the ecu, however the IAT table makes a massive difference. From what i see a lot of tuners dont think outside the box and realise just how important having an Air temp sensor, and the correct corresponding numbers in the table.

Im not sure if you can do anything about the barometric pressure compensation, as that should be built into the firmware of the ecu, however the IAT table makes a massive difference. From what i see a lot of tuners dont think outside the box and realise just how important having an Air temp sensor, and the correct corresponding numbers in the table.

Any competant tuner would usually turn away any map based ecu if it lacked an IAT sensor... well around here anyway.

Any competant tuner would usually turn away any map based ecu if it lacked an IAT sensor... well around here anyway.

Couldnt agree more, but ive seen tuner do installs without them enough to know it happens around here, usually the excuse is the owner didnt want to spend the extra for the sensor and install! Crazy.

hey there,

just figured out the backfire/hesitation is when boost starts building when its cold, when the engine isnt warmed up

also there is no cold start up set on the LINK either yet?

ideas??????????????????????

Are you anywhere near rips, i would take it to them. If you can put up screen shots of the settings in the software then it will make it easier.

hey, no which sucks, about 15 hrs away, bummer though i sponsor Robbie Ward at RIPS, ha.......

will try getting that info

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...