Jump to content
SAU Community

Recommended Posts

Last night i was doing a photoshoot of my car and my waterpump decided to go bye bye, it only just started leaking a bit so i am going to change it, does anyone know where i can get a waterpump from???? i dont need a timing belt service kit as i changed all my belts and water pump 40k ago on the motor. and would anyone have the genuine nissan number for the water pump????

to suit

1995 R33 series II motor

Edited by slverbullet
Link to comment
https://www.sau.com.au/forums/topic/269295-rb25det-water-pump/
Share on other sites

Tweakit in Mona Vale sell RB25 water pumps for $80. Not genuine Nissan, but it's the same brand pump as my mate runs in his drift 180SX and it hasn't skipped a beat. Click here for Tweakit's website thingy.

If I where you I'd change the timing belt regardless considering you have to remove it to get at the pump anyway, but that's just me :D

Didnt you guys read his questions? he specifically asked for the OEM Part Number with X3 question marks "???"

lol

anyhow

the Oem water pump number is 21010-21u25 for ALL......

The original poster seems so upset that we missed that part... oh wait!

thanks mate i will pick one up from there sometime this week, that is cheaper than everyelse that i have found.
The original poster seems so upset that we missed that part... oh wait!

not that i was trying to offend

but its just that ive noticed some people try and sound like they know what they are talking about but reply a message/2cents just for the sake of it or just to be heard about...

especially technical side of things, most replies are just half arsed...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just a thought, was that car and auto at any point of its life? If so, maybe whoever bridged the inhibitor switch/circuit did a not so good job.
    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
×
×
  • Create New...