Jump to content
SAU Community

Recommended Posts

I plugged in a cigarette lighter powered air compressor, and it stopped almost as quick as it started. Now the cigarette lighter doesn't work, I assume it's a blown fuse.

But looking at the fuses located under the bonnet, near the battery all were okay, so I assume there must be a fuse for the cig. lighter inside the dash somewhere?

Any suggestions?

Link to comment
https://www.sau.com.au/forums/topic/269334-cigarette-lighter-fuse/
Share on other sites

check to the right of your peddles

this pic is of the G35 (left hand drive) so filp it around and you have ours. (i think)

Thanks V35 Paul, it was where you said. After you pull the flap off, the fuse for the cigarette lighter is just to the left of the impliment provided to pull the fuses out, the 15 amp one.

Had to get some help from my a Japanese teacher at school to save me pulling them all out to check which one had blown.

All working now.

  • 6 months later...

Sorry to bring this thread up again but I am having trouble finding the lighter fuse on my car - a 2001 250GT sedan.

I can't seem to find the fuses as shown in the above diagram and while I found some fuses in the battery cavity, none seem to be for the lighter.

Can anyone advise where I should be looking for the cigarette lighter fuse on the 250GT sedan?

Hmm still don't seem to be able to find it.. Unless I should be pulling apart under the dash.. Found the computer cable and the home it lives but can't find fuses?

*Looking at Chris Rogers* Chris you are around these everyday.. Are you able to help??

Hmm still don't seem to be able to find it.. Unless I should be pulling apart under the dash.. Found the computer cable and the home it lives but can't find fuses?

*Looking at Chris Rogers* Chris you are around these everyday.. Are you able to help??

Most 12v sockets have a type of fuse attached directly to it, so remove the socket and have a look at the bottom of it, you should see it, basically looks like a thin metal wire that will have a break in it. Its so simple to fix, had a mate that tried to use a compressor and fried his sockets, the workshop quoted him $800 as they apparently had to take the whole dash out blah blah etc. I called BULLSHIT on it, told my mate what to do, so he ended up replacing the sockets himself for a few dollars.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...