Jump to content
SAU Community

Took off my kick panel to find........


kik-ass
 Share

Recommended Posts

High all, removed my left kick panel to install my new Power FC:D and found this. Looks like stock ECU but has a Mine's plate with serial no. on it. What does this mean?? Has it got a daughterboard or something in it? I know the stock ECU's are locked so what has been done? It will probably be up for sale in the near future once I know what it's worth

Link to comment
Share on other sites

Score!!!

Would seriously consider putting it on a dyno (if you haven't already) to see what the AFR's are like. i.e. make sure the ecu that is installed, isn't leaning out the mix too much due to the better fuel it was prob tuned on. Either way, i'd sell it and have an ecu that more people in this country know how to tune.

Adrian

Link to comment
Share on other sites

I have had the car for over 2 years now, runs sweet as. I always thought something was strange because the rev limiter doesn't cut in until around 8,000rpm or higher, and when I accidentally set my bleed valve wrong and boost went off my 20psi gauge the boost cut never cut in. Also I have the car over 220, definitely no speed cut either!! When I go to get the Power FC dyno tuned, I will make sure I get a run on this ECU first.

Link to comment
Share on other sites

thats like with my car!

i found this cool little plate with IMPUL racing written on it... it had clamps and looked like it belonged somewhere in the engine bay//

i was like... cool, theres some IMPUL work on my car!

but then i looked down at the pedals and realised that it clipped perfectly over the accelerator, prolly just taken off and put in the glovebox for compiance. not sure if its meant to be for that? but it fits nicely around it, so i now have an IMPUL pedal. anywayz... i got all excited for nothing...

Link to comment
Share on other sites

It'll do nicely for a few basic mods - but if you need to do anything too extravegant you'll have to send it back to Japan for repogramming.

Its better than the stock ECU, probably saves you having to buy an S-AFC, but its not the worlds greatest thing way down south.

This topic has been covered previously. May get $600 for it.

Link to comment
Share on other sites

ur car must have been running preety lean unless u were running on 98 + some octane booster or other additives with that mines ecu

Link to comment
Share on other sites

It would run lean as the mines ecu is tuned for 100+ octane jap fuel. Even if you just plug in the pfc and drive around and give it a glogging the engine check light will come on as it the base igniton and fuel maps are set for the jap fuel.

yes it would cause slight detonation but unless u know what you are listening for you wouldnt know!

Link to comment
Share on other sites

normal jap ones are ok but the mines one is mean to have real steep ign and fuel maps. Also depend on the mods done to the car when mines did the tune 2 i guess

Link to comment
Share on other sites

I also have a mines ECU in my R32 GTST...it has no speed limiter...i got the fuel all checked out and it was running lean...but only cos the old fuel pump was stuffed...put in a new fuel pump and she doesnt run lean anymore

Link to comment
Share on other sites

i always thought the car ran rich. When I bought the car, it was totally stock engine-wise, but it did have set of platinum plugs in a 7 heat range. Had the head off recently and internally the motor is very healthy. Only ever run it on 96-98 octane fuel, no booster. So all I know is that it ran the car fine in stock trim, and runs it sweet as with a full exhaust, front mount and more boost.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Unplug ECU. Unplug TPS. Unplug boost pressure sensor. Now, all the wires, placing your ground (black) multimeter lead at the ECU end, measure resistance of the 5V line at the boost sensor plug. Then do the same to the TPS plug. Then do the same for all the other wires that relate to the TPS, or boost sensor.   All of your measurements should be very very low. You're looking to see if wiring is out of wack here.   Secondly, from memory on the R33 (not a neo motor, so I'm assuming an r34) the ground wire for the TPS and boost sensor are NOT equal to ground of the car/battery. IE, DO NOT connect ground of the sensor to the engine/body of car. You'll get a ground loop, and/or potentially screw shit up. In electronics, ground for a circuit, is not necessarily equal to ground of another circuit.   So this leads me to ask, when measuring your 5V, how are you getting 1.5V? Where are your multimeter leads touching for both the red and black lead on the multimeter?   If you're measuring power on the sensor wire, and putting ground on the car chassis or negative battery terminal, that could be all of your issues in "getting 1.5v". Electronics engineers can do some funky stuff with circuits, and when both sensors are on, it's enough laid to alter how the ECU is functioning.
    • Nissan Oz are too busy trying to decide whether we need a Qashqai or Xtrail (whatever the difference is), really not a new issue. At least we can import cars they decided not to directly, at much better value. BTW can I confirm ADM Q50 all have no spare tyre (just goop)? Is that the same in JDM skyline? I'm going to need to sort something, I can't do billions of highway klm without a spare
    • Post up the manual extract and the wiring diagram (seeing as we've got no idea what type of car we're talking about here) to help with decision making. (Also, I'm nowhere near home and my wiring diagrams and manuals). I wouldn't suggest you do what you mentioned above on such a vague description, for a start! Depends on whether the power is from the ECU or the ground is at the ECU.
    • Hi all quick update, so i checked the wiring circuit on TPS / Boost sensor, everything checks out fine. So at this point im really leaning towards 2nd fried boost sensor due to bad ecu maybe? Is there a way or value to check for when ohm testing the boost sensor? Also is there a way to bypass the boost sensor? Thankyou
    • Many thanks for your responses, guys.
×
×
  • Create New...