Jump to content
SAU Community

Recommended Posts

Hey all,

i love my auto V cause its a daily drive, and traffic is in sydney is crap as we all know.

But when im just driving around, i love flicking it into semi auto mode and going through the gears as per a manual.

Problems i have!!!

#1 it seems when the car is cold (i duno why) shifting up seems to lag ALOT. you go to 2nd, then it wont go to 3rd until it wants to, which takes 2-5 pushes up on the gearshift. This is very annoying as the car revs out and it sounds like i cant drive.

#2 is the stupid system that doesnt allow gears at certain speeds. On the way up, 4th wont engage under 40 and 5th under 50. Now throwing it in auto mode is i guess the obvious thing to do, but its sometimes just annoys me. And on the way down aswell, i like how it'll let you flick from 4th to 2nd with a few flicks, but not being able to get into 1st over 50km/ph, sometimes is annoying and more so on the track. I know its to save the engine, but c'mon, its a strong engine!

Is there anything that can be done? ECU? Retune?

I guess i should have got the manual :)

Edited by V35 Matt

I haven't driven the auto, but on the CVT, the grounding cables helped. I can't say the lag was that bad before, but afterwards the changes were super-instant. The G35 guys reported similar results on their auto's if i can remember correctly.

Find a good auto tranny specialist and get them to beef it up. What they usually do is give it a service, change some solenoids/increase pressure and it will give firmer quicker shifts. I guess at the same time you can look at upgrading it slightly for more power if you want too!

Grounding wires ain't a bad idea. Some factory ground points are so crap it's unbelievable (dunno on the 350gt though, mine's a manual).

I'd be giving Mike from MV Automatics in adelaide a call, he's a guru when it comes to autos, especially jap stuff, if anyone's played with them in aus yet id put money on him.

Getting a normal valve body done usually ranges from 250-500 bucks. He does fully manual control boxes for earlier skyline stuff so he might be able to sort something out the V box.

I'd be giving Mike from MV Automatics in adelaide a call, he's a guru when it comes to autos, especially jap stuff, if anyone's played with them in aus yet id put money on him.

Getting a normal valve body done usually ranges from 250-500 bucks. He does fully manual control boxes for earlier skyline stuff so he might be able to sort something out the V box.

+1

I know that MV do a "stage 1" kit for the M35 Stagea, so I would hazard a guess that they would also have one for the V35 as both cars use a similar 5 speed tiptronic transmission.

They will also ship to whichever city you are in.

Edited by iamhe77
#2 is the stupid system that doesnt allow gears at certain speeds. On the way up, 4th wont engage under 40 and 5th under 50. Now throwing it in auto mode is i guess the obvious thing to do, but its sometimes just annoys me. And on the way down aswell, i like how it'll let you flick from 4th to 2nd with a few flicks, but not being able to get into 1st over 50km/ph, sometimes is annoying and more so on the track. I know its to save the engine, but c'mon, its a strong engine!

i can understand not being able to downshift above certain speeds... downshiting into 1st at 80kmh aint the smartest idea.. but yeh itsannoying not holding gears as you slow down.. the damn ford territory holds gears all teh way till stop and the V doesnt!? that shit aint right

to be honest the 'tiptronic' mode of our gearboxes is pretty poor. you have SOME input to what gear it will be in, but if the computer says no, its not gonna happen.

as for it not being able to shift down when youre slowing, thats not to save the engine. its to save the gearbox and the drivetrain

I read a lot of comments yesterday about the earthing kits on the G35 Driver site. There are a lot of reviews from people claiming improved shifting of the gear box and response from the motor. They are not claiming more hp, just an improvement in smoothness of the motor, more instant throttle response (that would not be hard on a M35) and faster shifts in manual mode.

All these things sound great and for the cost of a kit I will happily experiment with the idea. Just got to find a good kit now.

I emailed 2 people offering kits (the better reviewed ones) and 1 replied. I sent some images of the M35 motor and he can not guarantee it will fit as there are some major differences in the intake and not the same earthing points. He was not confident to say it would work without seeing the engine which might be a bit hard.

If anyone knows of a kit locally and a contact that would be great?

Cheers

Andy

Let us know how you go as I'm keen to put one on my car, i think it has some earth issues.

The kits you inquired about are they for US spec left hand drive cars? as the battery is located on the other side of the engine bay, would a universal kit perhaps be a better option?

Edited by NA_R33
Let us know how you go as I'm keen to put one on my car, i think it has some earth issues.

The kits you inquired about are they for US spec left hand drive cars? as the battery is located on the other side of the engine bay, would a universal kit perhaps be a better option?

Yes, they are for the left hand drive cars with battery on the opposite side. The V35 may not have as big a problem with compatibility as the only thing they seemed worried about was the earth on the plenum.

The universal kit may be easier but I am not sure if they would be as good. I read about one kit from a name brand that got really bad reviews but the ones designed for the G35 that included earths to gearbox and ECU seemed to rate very well.

I might have to do a better search on the Japanese sites but the US sites a so much easier to understand. Some one has to teach those yanks to drive on the correct side of the road! LOL :P

Edited by andy65b

i find that the manual shifts are best if u put it in the v35's power mode in terms of response and shifting wen u want it to as i can go to redline if u really wanted to (done it a few times :P ). however, with it will auto-downshift if ur not travelling fast enough. thats just my 2 cents hope that helps

andy just make the earthing kits yourself, its wire with crimped ends you screw onto the engine/gearbox etc. go to jaycar and buy all that stuff

but yeah i agree, all stock cars suffer from bad earthing!

Wonder if this would make a difference

(The “Sprint Booster”, is the perfect solution to solve the laggy of drive-by-wire system)

http://www.999automotive.com.au/products/sprintbooster/sprintbooster.html

My cousin used to have a Sprint Booster on his Golf GTi Mark V. The only thing it did was amplify the throttle response - meaning, if you depressed the accelerator at a normal 20%, it will amplify it to maybe 50-60%, making your car "feel" like it has improved throttle response.

However, I feel that it is a total waste of money and just a placebo. You can easily depress the throttle to 50-60% yourself and get the acceleration required. It increases fuel consumption and is too sensitive for accurate throttle control when you are hitting the apex of a turn.

Anyway my cousin enjoyed his sprint booster on his GTi for awhile then regretted buying it and sold it away.

Edited by siglapian

def. recommend the grounding wires

power delivery was noticeably improved due to better throttle response, didn't feel as laggy when shifting. Again, probably made f'all difference to power, just made the power delivery better via the gearbox

This car was my first auto and the earthing kit made it that much more bearable :)

still miss driving manual but meh

Edited by Yo-Yo

I bought a voltage stabiliser kit from a shop near me, I know the owner so he hooked me up with the pricing,

really you can buy any 4/8 awg cables and washer terminals if you know what you're doing. all stuff you can get from Jaycar

In regards to US kits I'm sure it would just be a case of reversing the install instuctions from right to left, the cables would be the same length and as long as common sense is used you can install them, us spec G's aren't any wider than japan-spec V's, just battery and wheel on opposite sides.

yes I installed mine, easy, find a ground to the body, the engine block and your throttle body if able

IMG_0052.jpg

IMG_0058.jpg

IMG_0059.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
×
×
  • Create New...