Jump to content
SAU Community

Recommended Posts

Hi guys,

Trying to install an aftermarket gauge in it and am having trouble removing the old oil pressure switch, how the hell does it come out? Ive tried unscrewing it by hand, but its way too tight (running low on that muscle growth protein stuff) and don't have a spanner/socket that fits over it. Not that it would matter as its just round with a notch in it.

Any tips? I need to do this by tomorrow for the track day. HELP!!!

Link to comment
https://www.sau.com.au/forums/topic/270190-removing-oil-pressure-switch/
Share on other sites

  • 2 weeks later...
ahh dont i feel stupid.

theres a 17mm nut in the back. no spanner long enough and got big hands so no access... :rofl:

How did you end up getting it off? I am stuck with the exact same problem. Tried from top and underneath by hand and with a 17mm spanner. Because the sender is tucked in I am having trouble getting the spanner square on it, and consequently am rounding the nut :D

In a fit of rage I soaked the bastard with WD-40 but I doubt it will be enough.

ahh, yeh it was an absolute bitch to get off... had to get under the car, squeeze my hands in there somehow, than got my bro to pass me a hammer from above and slowly knocked it out. there's no easier way from what i can see, just need a really skinny and long 17mm spanner and patience i guess.

my local tuning shop quoted me $50 to install the whole lot in to the car so that's not a bad price i guess, just i needed it done the night before a track day.

good luck with it!

ahh, yeh it was an absolute bitch to get off... had to get under the car, squeeze my hands in there somehow, than got my bro to pass me a hammer from above and slowly knocked it out. there's no easier way from what i can see, just need a really skinny and long 17mm spanner and patience i guess.

my local tuning shop quoted me $50 to install the whole lot in to the car so that's not a bad price i guess, just i needed it done the night before a track day.

good luck with it!

Thanks for the reply Marko. I finally got it!, and it wasn't too hard with the right tools.

I ended up using the following beast of a tool combination:

Economy Strap Oil Filter Wrench (1/2" socket with ring strap) -to- small extension bar -to- 1/2" universal joint -to- 450mm 1/2" extension bar -to- 1/2" Ratchet.

This allowed me to get the 1/2" bar up and above the intake plenum and thus put some nice leverage on it. Even with all that shit it still wasnt going to give up without a fight, had to swap Ratchet for Breaker Bar :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...