Jump to content
SAU Community

Recommended Posts

Possible things I can think of:

Loom from Engine > Ignitor

Ignitor

Loom from Ignitor > Coilpack

Coilpack

Coilpack Tips

Sparkplugs

o2 sensors

AFM

Injector stuck open

Intercooler leak

SO Ive started going through and changing items,

Loom from Engine > Ignitor

Ignitor

Loom from Ignitor > Coilpack

Coilpack

Coilpack Tips

Sparkplugs - cleaned and gapped, will replace with new ones asap

o2 sensors Cut and rejoined to install

AFM

Injector stuck open

Intercooler leak

Car had dead o2 sensors when bought, they have been replaced at the same time as some other items:

2 New injectors, all new o-rings

02 sensors replaced

FMIC taken off

Clutch installed

Intercooler pipes around turbos taken off.

Car is running very rich, any other suggestions as too what it could be would be much appreciated,

Edited by JiN_MaN
Link to comment
https://www.sau.com.au/forums/topic/270272-rb26-misfire/
Share on other sites

Loom from Engine > Ignitor

Ignitor

Loom from Ignitor > Coilpack Tested other one, no difference

Coilpack Tested other ones, no difference

Coilpack Tips New ones fitted

Sparkplugs - cleaned and gapped, will replace with new ones asap Replaced

o2 sensors Replaced but cut and rejoined wires to install

AFM

Injector stuck open

Intercooler leak Looked over all seems good.

+ Reset ECU

Edited by JiN_MaN
Link to comment
https://www.sau.com.au/forums/topic/270272-rb26-misfire/#findComment-4598733
Share on other sites

Bad batch of fuel?

How does it idle (and what does it show the vacuum pressure as when idling)?

If you don't run a FPR, look into the pressure regulator

Does your ECU give you an error code(s)?

How is compression in each cylinder?

Edited by Moodles2
Link to comment
https://www.sau.com.au/forums/topic/270272-rb26-misfire/#findComment-4598783
Share on other sites

Bad batch of fuel?

How does it idle (and what does it show the vacuum pressure as when idling)?

If you don't run a FPR, look into the pressure regulator

Does your ECU give you an error code(s)?

How is compression in each cylinder?

fuel filter... :( ?

running standard ECU?

Is the ignitor grounded?

If not do it!

Will look into all these suggestions today and update, Thanks for the help, keep it coming, Ill take ANY suggestions,

Standard ECU, supposedly remapped my mines

Edited by JiN_MaN
Link to comment
https://www.sau.com.au/forums/topic/270272-rb26-misfire/#findComment-4599381
Share on other sites

Ill also add, I started and drove it in Japan, just up and down the road and it idled fine, but when I first picked it up in aus it had the front bar moved and the intercooler hoses on both ends off. It was all removed in Japan.

Havent got it to idle since, Compression test came up with 155-153psi across all cylinders.

Link to comment
https://www.sau.com.au/forums/topic/270272-rb26-misfire/#findComment-4600826
Share on other sites

ok, that changes things. if the only thing that's changed since it was driving fine japan is piping then most likely you have a leak somewhere, or something is not connected properly (ie hoses back to front, swapped etc). you need to go over all the piping again. why was piping removed between here and japan?

Link to comment
https://www.sau.com.au/forums/topic/270272-rb26-misfire/#findComment-4601370
Share on other sites

ok, that changes things. if the only thing that's changed since it was driving fine japan is piping then most likely you have a leak somewhere, or something is not connected properly (ie hoses back to front, swapped etc). you need to go over all the piping again. why was piping removed between here and japan?

I assume it was to remove the front bar for shipping, and they hadn't done it before, all bolts to remove the front lip from the front bar had been removed and kept in bag.

Link to comment
https://www.sau.com.au/forums/topic/270272-rb26-misfire/#findComment-4603495
Share on other sites

the symptoms really do point to an air leak. even more so considering the chain of events:

car started, idled and drove fine.

you left car

piping was removed/messed with

piping was replaced

car wont idle, run or drive properly

I know where I'd be hunting the problem. leaks wont always be visible to the naked eye. go over every piece of induction piping.

Link to comment
https://www.sau.com.au/forums/topic/270272-rb26-misfire/#findComment-4603671
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...