Jump to content
SAU Community

Recommended Posts

I have a problem with my car again its a R33 S2 and it is missfiring, I know this topic has been covered tons of times but I have fixed the missfire previously by buying new coilpacks. I bought JJR coilpacks and the missfire was gone for maybe 6 months, the car reved very smoothly all the way to redline... and now I'm getting a missfire at about 5000-5500rpm and up until then the car feels flat like it has no balls and then at about 6000rpm it feels like it takes off until redline.

Could this be that the coilpacks have fudged them selves?

Also I have replaced the spark plugs with iridium ones about 6 months ago just before i changed the coilpacks.

Any ideas? Could it be a injector?

Link to comment
https://www.sau.com.au/forums/topic/271189-missfiring-again/
Share on other sites

there is a sticky in general maintenance, they say to tape up your coils due to tiny cracks in them(electrical tape). Might be worth checking a very cheap option, at least the u can diagnose the problem this way.

+1

Worked for me

there is a sticky in general maintenance, they say to tape up your coils due to tiny cracks in them(electrical tape). Might be worth checking a very cheap option, at least the u can diagnose the problem this way.

I got new JJR coils, they shouldnt need to be taped...but i guess if it stops missfirring when they are taped then this just means they are arking out then they are fooked...

My plugs are gapped to the standard irridium plug size which is 12mm i think. But they shouldnt need to be gapped if i got new coil packs rite??? They should be strong enough to make the spark jump accross stock gapped spark plugs?

Edited by da spike

change the plugs to BCPR6ES gapped to .8mm then put a little mark in texta on the spark plug where the electrode is open (ie where you can see the most of it) when doing up your spark plugs point that mark to the inlet manifold you would be surprised how often this will fix your problems you want the mixture to be ignited if the electrode is facing the exhaust manifold it wont run as well small point but makes a big difference

I'm interested in seeing what happens. I have spitfire coils and gapped my plugs to 0.8mm as almost everyone recommends and it run absolutely crap after 4,000 rpm, gapped them to 1.1 and revs out to redline beautifully.

i installed my splitfires today along with new plugs gapped to 0.8mm, idle's fine but when i go to drive my car is missfires hardcore even at low revs...! rkn i should regap to atleased 1mm?

Another question... how do you guys gap the plugs without fooking them? Just tap them down with a small hammer?

I just gave it kinda firm knocks on my workbench and a feeler gauge to verify the gap - seemed to do the trick fine.

I'm just thinking could this be RnR? Because i would find it hard to believe that the coilpacks would have shit them selves after a few months use and i have changed the sparkies too when changing coilpacks to irridium ones... The missfire or popping under acceleration usually happens on a really cold night, the car also feels like it has a flat spot from 4500rpm to 6000rpm and then from 6 onwards its fine...

if it is happening more when it is cold then it may be rnr. but remember that the VCT turns off at 4500rpm so you do get a bit of a flat spot there.

to gap the plugs you need a feeler gauge. basically it is a set of small sheets of metal all different sizes.

i personally think iridium spark plugs are a waste of time. the set in my old 33 were shagged after about 20,000kms. i put the ones listed above in and changed them after 10,000kms and they were still fine. they are only a few dollars a plug.

as for there the tip of the plug is and marking it with a pen and trying to align it with the manifold, you may find that doesn't always work, without ending up with either it too loose or way too tight. however it shouldn't really make a difference as the valve will be closed well before the spark plug fires

Ok I got BCPR6ES plugs and threw them in and took the car for a spin just quickly and it looks like its not missfiring anymore... :D But I will need to drive it more to make sure because sometimes the missfire would be tempremental..

But what it's still doing is running shit from about 4500rpm all the way to 6000rpm and then it kicks in hard. Do you guys think this is rnr?

By the way I'm running standard boost and its going up to about 9-10psi cause its a cold night and exhaust, intercooler.

i personally think iridium spark plugs are a waste of time. the set in my old 33 were shagged after about 20,000kms. i put the ones listed above in and changed them after 10,000kms and they were still fine. they are only a few dollars a plug.

The iridium ones i took out (i put these in about 10,000 kms ago) were pretty fouled up so i guess copper ones are the cheaper alternative...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...