Jump to content
SAU Community

Recommended Posts

S1 Stagea rs4 auto.

OK so here's what I have so far laying around:

Intake plenum

80mm throttle body

top mount exhaust manifold

600x300 FMIC

cam gears

kkr430 (itll do for now, until I get a gt3540 and a wastegate)

splitfires

BOV

Mate's trying to talk me into some top feed injectors (550cc?)

ECU - Im looking at a Greddy emanage ultimate, the powerfc i think is just screaming 'overboard' to me.

Anything else I need? Looking at putting this on in July when we do the big roadtrip to C-red.

Thanks in advance, my knowledge is starting to lack at this stage

Link to comment
https://www.sau.com.au/forums/topic/271286-s1-upgrades/
Share on other sites

Fuel pump Bosch or Walbro. Either fpr or bigger injectors (why topfeed - you can get 550 side feed nothing wrong with stock rail). Greddy E-manage best bet for S1 auto. I haven't got anything on your list except for an adjustable exhaust cam gear - spent my money on a GCG highflow instead. Next 550 (sidefeed) injectors and Z32afm.

Link to comment
https://www.sau.com.au/forums/topic/271286-s1-upgrades/#findComment-4611786
Share on other sites

S1 requires ecu to run auto at all (even though there is another computer for the auto) let alone pull timing during changes etc. Pretty sure PFC won't work - haven't heard of anyone doing it on an S1 auto - hence the e-manage. Stock injectors OK for around 200AWKW - fpr may push that up a little - if your aim is big horsepower (240AWKW say) then forget the fpr and get the bigger injectors when needed.

PS 200AWKW makes for a pretty rapid wagon.

Link to comment
https://www.sau.com.au/forums/topic/271286-s1-upgrades/#findComment-4612120
Share on other sites

PFC will work, just no timing retard on changes, there are people running auto r33's with PFC's
but are they skylines or stageas? I am having this issue right now...Stagea with ov300 needs that ecu to make auto work at all - tuner is piggybacking R32 ecu to fit tunable chip but has to leave ov300 as well or I'm stuck in 3rd gear. Not an issue with R33 skylines or R34 S2 stageas.
Link to comment
https://www.sau.com.au/forums/topic/271286-s1-upgrades/#findComment-4612329
Share on other sites

Have you determined what signals the Auto ECU is having a sook about not receiving from the factory ECU?
Apparently there are six pins involved but tuner is the electronics expert not me. Strangely with the same auto (but different ecu and loom ) Stagea S2 can do without the stock ecu ( and therefore run Vipec/Link) although ironically the S2 stock ecu can be Nistuned while the S1 cannot.
Link to comment
https://www.sau.com.au/forums/topic/271286-s1-upgrades/#findComment-4612409
Share on other sites

but are they skylines or stageas? I am having this issue right now...Stagea with ov300 needs that ecu to make auto work at all - tuner is piggybacking R32 ecu to fit tunable chip but has to leave ov300 as well or I'm stuck in 3rd gear. Not an issue with R33 skylines or R34 S2 stageas.

skylines, as i said, auto r33's

i would just go an EM-U instead of all that f**king around :)

Link to comment
https://www.sau.com.au/forums/topic/271286-s1-upgrades/#findComment-4612424
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm seeing torque specs all over the place for the OUTER tie rod, but none for the INNER tie rod, where it connects to the steering rack. Even in videos, people are just tightening em up as much as they can with a wrench and that's it. Anything tightened down without torque makes me nervous. Anyone know what the spec is for it?
    • Hope you had a great time here in our tiny country.   The JDM scene we have here is quite small, it's mostly BMW, Volkswagen with burble tunes haha. But the few JDM cars we do have in the scene are pretty nice. Some of my friends drive cool s14's too. Both built engines, red one makes abt 500, blue one abt 400 i think?
    • Ye good idea , would have never thought of something like that. Might aswell do it to every pulley and the balancer while I’m there 
    • Use an LS1 or similar, via kit like Frenchy's. But.... It's probably not the alternator. It sounds like belt squeal, which would be because the pulleys are glazed. Rub every groove on the pulleys with 120 grit paper. Report back. Oh, and new belts afterwards too. The old new ones will be shitted up already.
    • Hello all I have 2 r34 sedans , one turbo one na, only recently aquired the na 34.  Man what is with these things.... My turbo 34 started sounding like a super charger, it was screaming at anything above 4000rpm , I took the alternator apart and replaced the front bearing which is the only one I think you can access and it did not fix the issue so presumably the bearing in the rear of the alternator is gone. ( diagnosed it was the alternator by taking off the aux belts one by one to figure out which pulley or bearing it was )  My friend gave me one he had lying around, Installed it , it did not squeal for maybe 500kms and now its started to squeal again briefly on startup  Recently got an na r34 and I replaced the timing belt, water pump + all the auxillirary belts. Runs amazing but it suddenly developed the same squeaking problem but significantly worse, Ive had my neighbour come down screaming at me because it was waking her up everytime I moved the car. It takes a good 2 minutes before it quietens down.  Im yet to diagnose where its coming from but im fairly sure its coming from the alternator aswell. My question isnt about how to fix it but rather where can you get a new alternator for an rb25 neo??? Ive searched everywhere but I havent been able to find a direct fit oem type replacement thats not genuine. All the automotive stores sell an oex one - BXA035 - which I picked up for cheap through a friend with staff discount , got it home only to find the connector is completelty different.... As far as im aware bxa035 is for rb20/30's and after a bit of figuring out the bxa035 has an ev14 type connector, which is tiny compared to the rb25 connector. I actually had an ev14 connector lying around which I was considering just replacing the bigger plug with to get the alternator working but the bxa035 is rated for 70amp vs the rb25 alternators are 90amp ( or so ive been told ? ) That paired along with the fact im about to install an amp + sub in the back and I have the stock sized small battery Im not sure itll do the job unless anyone has another opinion?  I know and have seen all the websites selling the ls1 alternator conversion kit but I am not going down that route, nor do I have the money to. Hopefully I can figure out how to get 2 brand new alternators for both cars. I would buy second hand which there seems to be many of but considering how common this seems to be im sure If I installed a second hand one it would start squealing in no time  Or even better if anyone knows how to fix the issue directly with the alternator itself... Any input appreciated Thank you     Link for bxa035 connector picture
×
×
  • Create New...